This document specifies constructional, functional, testing and marking requirements, sizing and documentation of gas pressure regulators used in the pressure regulating stations in accordance with EN 12186 or EN 12279: for inlet pressures up to 100 bar and nominal diameters up to DN 400; for an operating temperature range from -20 °C to +60 °C, which operate with fuel gases of the 1st and 2nd family in accordance with EN 437 in transmission and distribution networks and also in commercial and industrial installations. "Gas pressure regulators" hereafter will be called "regulators" except in the titles. For standard regulators when used in pressure regulating stations complying with EN 12186 or EN 12279, Annex ZA lists all applicable Essential Requirements except the external corrosion resistance in case of environmental conditions where corrosion is likely to occur. This document considers the following classes/types of regulators: class 1: operating temperature range from -10 °C to 60 °C; class 2: operating temperature range from -20 °C to 60 °C; type IS: (integral strength type); type DS: (differential strength type). This document applies to regulators which use the pipeline gas as a source of control energy unassisted by any external power source. The regulator may incorporate a creep (venting) relief device, complying with the requirements in Annex F. The regulators complying with the requirements of this document may be declared as "in compliance with EN 334" and bear the marking "EN 334". This document does not apply to: regulators upstream from/on/in domestic gas-consuming appliances which are installed downstream of domestic gas meters; regulators incorporated into pressure-regulating devices used in service lines with volumetric flow rate 200 m3/h at normal conditions and inlet pressure 5 bar; regulators for which a specific document exists (e. g. EN 88, etc.); industrial process control valves in accordance with EN 1349.
EN 334:2005+A1:2009 Referenced Document
EN 10045-1:1989 Metallic materials; Charpy impact test; part 1: test method
EN 1092-1:2007 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 1: Steel flanges (Incorporates Amendment A1: 2013; Incorporating Corrigendum May 2014)
EN 1092-2:1997 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges
EN 1092-3:2003 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories PN designated - Part 3: Copper alloy flanges
EN 1092-4:2002 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 4: Aluminium alloy flanges
EN 1349:2000 Industrial Process Control Valves Incorporating Corrigendum October 2001
EN 1418:1997 Welding Personnel - Approval Testing of Welding Operators for Fusion Welding and Resistance Weld Setters for Fully Mechanized and Automatic Welding of Metallic Materials
EN 1759-1:2004 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, class designated - Part 1: Steel flanges, NPS 1/2 to 24*， 2024-04-20 Update
EN 1759-3:2003 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 3: Copper alloy flanges Incorporating Corrigendum July 2004
EN 1759-4:2003 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, class designated - Part 4: Aluminium alloy flanges
EN 287-1:2004 Qualification test of welders - Fusion welding - Part 1: Steels Incorporating Corrigendum August 2004; Includes Amendment A2:2006
EN 473:2000 Non-Destructive Testing - Qualification and Certification of NDT Personnel - General Principles includes amendment A1:2005; Supersedes CR 12459:1996*， 2024-04-20 Update
EN 970:1997 Non-Destructive Examination of Fusion Welds - Visual Examination
EN 334:2005+A1:2009 history
2019EN 334:2019 Gas pressure regulators for inlet pressure up to 10 MPa (100 bar)
2009EN 334:2005+A1:2009 Gas pressure regulators for inlet pressures up to 100 bar
2005EN 334:2005 Gas pressure regulators for inlet pressures up to 100 bar (Incorporates Amendment A1: 2009)
1999EN 334:1999 Gas Pressure Regulators for Inlet Pressures up to 100 Bar (Incorporates Amendment A1: 2000)