ASTM A333/A333M-16
Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service and Other Applications with Required Notch Toughness
- Standard No.
- ASTM A333/A333M-16
- Release Date
- 2016
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM A333/A333M-18
- Latest
- ASTM A333/A333M-24
- Scope
1.1 This specification2 covers nominal (average) wall seamless and welded carbon and alloy steel pipe intended for use at low temperatures and in other applications requiring notch toughness. Several grades of ferritic steel are included as listed in Table 1. Some product sizes may not be available under this specification because heavier wall thicknesses have an adverse effect on impact properties.
(A) For each reduction of 0.018201;% carbon below 0.308201;%, an increase of 0.058201;% manganese above 1.068201;% would be permitted to a maximum of 1.358201;% manganese.(B) Where an ellipsis (...) appears in this table, there is no requirement and analysis for the element need not to be determined or reported.(C) By agreement between the manufacturer and the purchaser, the limit for columbium may be increased up to 0.058201;% on heat analysis and 0.068201;% on product analysis.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.
Note 1: The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.”
ASTM A333/A333M-16 Referenced Document
- ASTM A370 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
- ASTM A671 Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures
- ASTM A999/A999M Standard Specification for General Requirements for Alloy and Stainless Steel Pipe
- ASTM E165 Standard Test Method for Liquid Penetrant Examination
- ASTM E23 Standard Test Methods for Notched Bar Impact Testing of Metallic Materials
- ASTM E709 Standard Guide for Magnetic Particle Examination
ASTM A333/A333M-16 history
- 2024 ASTM A333/A333M-24 Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service and Other Applications with Required Notch Toughness
- 2018 ASTM A333/A333M-18 Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service and Other Applications with Required Notch Toughness
- 2016 ASTM A333/A333M-16 Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service and Other Applications with Required Notch Toughness
- 2015 ASTM A333/A333M-15 Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service and Other Applications with Required Notch Toughness
- 2013 ASTM A333/A333M-13 Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service and Other Applications with Required Notch Toughness
- 2011 ASTM A333/A333M-11 Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service
- 2010 ASTM A333/A333M-10 Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service
- 2005 ASTM A333/A333M-05 Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service
- 2004 ASTM A333/A333M-04a Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service
- 2004 ASTM A333/A333M-04 Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service
- 1999 ASTM A333/A333M-99 Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service
- 1994 ASTM A333/A333M-94 Standard Specification for Seamless and Welded Steel Pipe for Low-Temperature Service
- 1967 ASTM A333-67 Standard Specifications For Seamless And Welded Steel Pipe For Low-Temperature Service
