ASTM F645-15a
Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems

Standard No.
ASTM F645-15a
Release Date
2015
Published By
American Society for Testing and Materials (ASTM)
Status
Replace By
ASTM F645-18
Latest
ASTM F645-18b
Scope

4.1 The requirements of this specification are intended to provide information to select, design and install thermoplastic, water-pressure piping systems for use outside buildings. Materials covered in this specification are Poly(Vinyl Chloride) (PVC) and Polyethylene (PE) plastic pipe fittings.

1.1 This guide is intended for use in the selection, design, and installation of thermoplastic water systems for use outside buildings. For specific projects, a thorough review of this guide is recommended for the purpose of selecting specific materials, methods of joining, system design factor, and any special procedures deemed necessary to assure a satisfactory system.

1.2 It is recommended that governing codes and project specifications be consulted prior to the use of this guide. Nothing in this guide should be construed as recommending practices or systems at variance with governing codes and project specifications.

1.3 Units-The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The pipe, fittings, and joining materials shall meet the requirements of one or more of the following component product standards listed in 1.3.1 through 1.3.4 to the extent applicable. Those pipe standards followed by (a) are outside diameter-controlled pipes. Those followed by (b) are inside diameter-controlled pipes.

1.3.1 For poly(vinyl chloride) (PVC) plastic piping components: 

8199;
Title of Specification

ASTM
Designation

Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80
8199;and 120 (a)

D1785

Poly(Vinyl Chloride) (PVC) Plastic Pipe (SDR-PR) (a)

D2241

Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings,
81......

ASTM F645-15a Referenced Document

  • ASTM C651 Standard Test Method for Flexural Strength of Manufactured Carbon and Graphite Articles Using Four-Point Loading at Room Temperature
  • ASTM C900 Standard Test Method for Pullout Strength of Hardened Concrete
  • ASTM C901 Standard Specification for Prefabricated Masonry Panels
  • ASTM D1600 Standard Terminology for Abbreviated Terms Relating to Plastics
  • ASTM D1784 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds
  • ASTM D1785 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120
  • ASTM D2239 Standard Specification for Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter
  • ASTM D2241 Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series)
  • ASTM D2464 Standard Specification for Threaded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80
  • ASTM D2466 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40
  • ASTM D2467 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80
  • ASTM D2564 Standard Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems
  • ASTM D2609 Standard Specification for Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe*， 2024-04-20 Update
  • ASTM D2672 Standard Specification for Joints for IPS PVC Pipe Using Solvent Cement
  • ASTM D2683 Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
  • ASTM D2737 Standard Specification for Polyethylene (PE) Plastic Tubing
  • ASTM D2740 
  • ASTM D2774 Standard Practice for Underground Installation of Thermoplastic Pressure Piping
  • ASTM D2855 Standard Practice for Making Solvent-Cemented Joints with Poly(Vinyl Chloride) (PVC) Pipe and Fittings
  • ASTM D3035 Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
  • ASTM D3139 Standard Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals
  • ASTM D3261 Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing
  • ASTM D3350 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials*， 2024-04-20 Update
  • ASTM F1498 Standard Specification for Taper Pipe Threads 60° for Thermoplastic Pipe and Fittings
  • ASTM F412 Standard Terminology Relating to Plastic Piping Systems
  • ASTM F439 Standard Specification for Socket-Type Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
  • ASTM F441/F441M Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80
  • ASTM F477 Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
  • ASTM F493 Standard Specification for Solvent Cements for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe and Fittings
  • ASTM F545 Specification for PVC and ABS Injected Solvent Cemented Plastic Pipe Joints (Withdrawn 2001)

ASTM F645-15a history

  • 2018 ASTM F645-18b Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
  • 2018 ASTM F645-18a Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
  • 2018 ASTM F645-18 Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
  • 2015 ASTM F645-15a Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
  • 2015 ASTM F645-15 Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
  • 2013 ASTM F645-13 Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
  • 2012 ASTM F645-12a Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
  • 2012 ASTM F645-12 Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
  • 2011 ASTM F645-11 Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems
  • 2004 ASTM F645-04 Standard Guide for Selection, Design, and Installation of Thermoplastic Water-Pressure Piping Systems
  • 2002 ASTM F645-02 Standard Guide for Selection, Design, and Installation of Thermoplastic Water-Pressure Piping Systems
  • 1995 ASTM F645-95 Standard Guide for Selection, Design, and Installation of Thermoplastic Water Pressure Piping Systems
Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems


Copyright ©2024 All Rights Reserved