ASTM E2047-10(2015)
Standard Test Method for Wet Insulation Integrity Testing of Photovoltaic Arrays

Standard No.

ASTM E2047-10(2015)

Release Date

2010

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM E2047-10(2019)

Latest

ASTM E2047-10(2019)

Scope

5.1 The design of a PV module or system intended to provide safe conversion of the sun's radiant energy into useful electricity must take into consideration the possibility of hazard should the user come into contact with the electrical potential of the array. In addition, the insulation system provides a barrier to electrochemical corrosion, and insulation flaws can result in increased corrosion and reliability problems. This test method describes a procedure for verifying that the design and construction of the array provides adequate electrical isolation through normal installation and use. At no location on the array should the PV-generated electrical potential be accessible, with the obvious exception of the output leads. The isolation is necessary to provide for safe and reliable installation, use, and service of the PV system.

5.2 This test method describes a procedure for determining the ability of the array to provide protection from electrical hazards. Its primary use is to find insulation flaws that could be dangerous to persons who may come into contact with the array. Corrective action taken to address such flaws is beyond the scope of this test method.

5.3 This procedure may be specified as part of a series of acceptance tests involving performance measurements and demonstration of functional requirements. Large arrays can be tested in smaller segments. The size of the array segment to be tested (called “circuit under test” in this test method) is usually selected at a convenient break point and sized such that the expected resistance or current reading is within the middle third of the meter's range.

5.4 Insulation leakage resistance and insulation leakage current leakage are strong functions of array dimensions, ambient relative humidity, absorbed water vapor, and other factors. For this reason, it is the responsibility of the user of this test method to specify the minimum acceptable leakage resistance for this test.

5.4.1 Even though a numerical quantity is specified, actual results are often pass-fail in that when a flaw is found, the leakage current changes from almost nothing to the full scale value on the meter.

5.5 The user of this test method must specify the option used for connection to the array during the test. The short-circuited option requires a shorting device with leads to connect the positive and negative legs of the circuit under test. For larger systems, where the shorting device may have to be rated for high current and voltage levels, the open-circuited option may be preferred. The open-circuited option requires the user to correct readings to account for the PV-generated voltage, and the procedure for making such corrections is beyond the scope of this test method. The short-circuited option may be easier for small systems where the voltage and current levels are low and the distance between the plus and minus leads of the circuit under test are small. The short-circuited option minimizes the chance of exposing array components to voltage levels above those for which they are rated.

1.1 This test method covers a procedure to determine the insulation resistance of a photovoltaic (PV) array (or its component strings), that is, the electrical resistance between the array's inter......

ASTM E2047-10(2015) Referenced Document

• ASTM E1328 Standard Terminology Relating to Photovoltaic Solar Energy Conversion
• ASTM E1462 Standard Test Methods for Insulation Integrity and Ground Path Continuity of Photovoltaic Modules
• ASTM E772 Standard Terminology Relating to Solar Energy Conversion

ASTM E2047-10(2015) history

• 2019 ASTM E2047-10(2019) Standard Test Method for Wet Insulation Integrity Testing of Photovoltaic Arrays
• 2010 ASTM E2047-10(2015) Standard Test Method for Wet Insulation Integrity Testing of Photovoltaic Arrays
• 2010 ASTM E2047-10 Standard Test Method for Wet Insulation Integrity Testing of Photovoltaic Arrays
• 2005 ASTM E2047-05 Standard Test Method for Wet Insulation Integrity Testing of Photovoltaic Arrays
• 1999 ASTM E2047-99 Standard Test Method for Wet Insulation Integrity Testing of Photovoltaic Arrays