ASTM C1107/C1107M-14a PDF

Scope: 1.1 This specification covers packaged dry, hydraulic cement grout (nonshrink) intended for use under applied load (such as to support a structure, a machine, and the like) where a change in height below initial placement height is to be avoided.

1.2 Grouts covered are composed of hydraulic cement, fine aggregate, and other ingredients. They require only the addition of mixing water for use.

1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.4 The following safety hazards caveat pertains only to the test method portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM C1107/C1107M-14a Referenced Document

ASTM C109/C109M Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)
ASTM C1090 Standard Test Method for Measuring Changes in Height of Cylindrical Specimens from Hydraulic-Cement Grout
ASTM C125 Standard Terminology Relating to Concrete and Concrete Aggregates
ASTM C138/C138M Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete
ASTM C1437 Standard Test Method for Flow of Hydraulic Cement Mortar
ASTM C157/C157M Standard Test Method for Length Change of Hardened Hydraulic-Cement, Mortar, and Concrete
ASTM C185 Standard Test Method for Air Content of Hydraulic Cement Mortar
ASTM C305 Standard Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency
ASTM C702 Standard Practice for Reducing Samples of Aggregate to Testing Size
ASTM C827 Standard Test Method for Change in Height at Early Ages of Cylindrical Specimens of Cementitious Mixtures
ASTM C939 Standard Test Method for Flow of Grout for Preplaced-Aggregate Concrete (Flow Cone Method)

2020 ASTM C1107/C1107M-20 Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink)
2017 ASTM C1107/C1107M-17 Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink)
2014 ASTM C1107/C1107M-14a Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink)
2014 ASTM C1107/C1107M-14 Standard Specification for Packaged Dry, Hydraulic-Cement Grout 40;Nonshrink41;
2013 ASTM C1107/C1107M-13 Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink)
2011 ASTM C1107/C1107M-11 Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink)
2008 ASTM C1107/C1107M-08 Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink)
2007 ASTM C1107/C1107M-07a Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink)
2007 ASTM C1107/C1107M-07 Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink)
2005 ASTM C1107-05 Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink)
2002 ASTM C1107-02 Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink)
1999 ASTM C1107-99 Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink)