ASTM F3122-14
Standard Guide for Evaluating Mechanical Properties of Metal Materials Made via Additive Manufacturing Processes

Standard No.

ASTM F3122-14

Release Date

2014

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM F3122-14(2022)

Latest

ASTM F3122-14(2022)

Scope

1.1 This standard serves as a guide to existing standards or variations of existing standards that may be applicable to determine specific mechanical properties of materials made with an additive manufacturing process.

1.2 As noted in many of these referenced standards, there are several factors that may influence the reported properties, including material, material anisotropy, method of material preparation, porosity, method of specimen preparation, testing environment, specimen alignment and gripping, testing speed, and testing temperature. These factors should be recorded, to the extent that they are known, according to Practice F2971 and the guidelines of the referenced standards.

1.3 The following standards are not referred to directly in the guide but also have information that may be useful in the testing of metal test specimens made via additive manufacturing: A370, A1058, B211, B348, B557, B565, B724, B769, E3, E6, E7, E290, E467, E468, E837, E915, E1049,E1823, E1942.

1.4 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F3122-14 Referenced Document

• ASTM A1058 Standard Test Methods for Mechanical Testing of Steel Products—Metric*， 2024-04-20 Update
• ASTM A370 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
• ASTM B211 Standard Specification for Aluminum and Aluminum-Alloy Bar, Rod, and Wire
• ASTM B348 Standard Specification for Titanium and Titanium Alloy Bars and Billets
• ASTM B557 Standard Test Methods of Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
• ASTM B565 Standard Test Method for Shear Testing of Aluminum and Aluminum-Alloy Rivets and Cold-Heading Wire and Rods
• ASTM B645 Standard Practice for Plane-Strain Fracture Toughness Testing of Aluminum Alloys
• ASTM B646 Standard Practice for Fracture Toughness Testing of Aluminum Alloys
• ASTM B647 Standard Test Method for Indentation Hardness of Aluminum Alloys by Means of a Webster Hardness Gage
• ASTM B648 Standard Test Method for Indentation Hardness of Aluminum Alloys by Means of a Barcol Impressor
• ASTM B724 Standard Test Method for Indentation Hardness of Aluminum Alloys by Means of a Newage, Portable, Non-Caliper-Type Instrument
• ASTM B769 Standard Test Method for Shear Testing of Aluminum Alloys
• ASTM B909 Standard Guide for Plane Strain Fracture Toughness Testing of Non-Stress Relieved Aluminum Products
• ASTM E10 Standard Test Method for Brinell Hardness of Metallic Materials
• ASTM E1049 Standard Practices for Cycle Counting in Fatigue Analysis
• ASTM E111 Standard Test Method for Young''s Modulus, Tangent Modulus, and Chord Modulus
• ASTM E1221 Standard Test Method for Determining Plane-Strain Crack-Arrest Fracture Toughness, K_Ia, of Ferritic Steels
• ASTM E1290 Standard Test Method for Crack-Tip Opening Displacement (CTOD) Fracture Toughness Measurement
• ASTM E1304 Standard Test Method for Plane-Strain (Chevron-Notch) Fracture Toughness of Metallic Materials
• ASTM E132 Standard Test Method for Poisson''s Ratio at Room Temperature
• ASTM E140 Standard Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness, Superficial Hardness, Knoop Hardness, and Scleroscope Hardness
• ASTM E143 Standard Test Method for Shear Modulus at Room Temperature
• ASTM E1450 Standard Test Method for Tension Testing of Structural Alloys in Liquid Helium
• ASTM E1457 Standard Test Method for Measurement of Creep Crack Growth Times in Metals
• ASTM E1681 Standard Test Method for Determining a Threshold Stress Intensity Factor for Environment-Assisted Cracking of Metallic Materials
• ASTM E18 Standard Test Methods for Rockwell Hardness of Metallic Materials
• ASTM E1820 Standard Test Method for Measurement of Fracture Toughness
• ASTM E1823 Standard Terminology Relating to Fatigue and Fracture Testing
• ASTM E1875 Standard Test Method for Dynamic Young's Modulus, Shear Modulus, and Poisson's Ratio by Sonic Resonance
• ASTM E1876 Standard Test Method for Dynamic Young's Modulus, Shear Modulus, and Poisson's Ratio by Impulse Excitation of Vibration
• ASTM E1942 Standard Guide for Evaluating Data Acquisition Systems Used in Cyclic Fatigue and Fracture Mechanics Testing
• ASTM E209 Standard Practice for Compression Tests of Metallic Materials at Elevated Temperatures with Conventional or Rapid Heating Rates and Strain Rates
• ASTM E21 Standard Test Methods for Elevated Temperature Tension Tests of Metallic Materials
• ASTM E23 Standard Test Methods for Notched Bar Impact Testing of Metallic Materials
• ASTM E2368 Standard Practice for Strain Controlled Thermomechanical Fatigue Testing
• ASTM E238 Standard Test Method for Pin-Type Bearing Test of Metallic Materials
• ASTM E2472 Standard Test Method for Determination of Resistance to Stable Crack Extension under Low-Constraint Conditions
• ASTM E2714 Standard Test Method for Creep-Fatigue Testing
• ASTM E2760 Standard Test Method for Creep-Fatigue Crack Growth Testing
• ASTM E2789 Standard Guide for Fretting Fatigue Testing
• ASTM E290 Standard Test Methods for Bend Testing of Material for Ductility
• ASTM E292 Standard Test Methods for Conducting Time-for-Rupture Notch Tension Tests of Materials
• ASTM E3 Standard Practice for Preparation of Metallographic Specimens
• ASTM E384 Standard Test Method for Microindentation Hardness of Materials
• ASTM E399 Standard Test Method for Plane-Strain Fracture Toughness of Metallic Materials
• ASTM E448 Standard Practice for Scleroscope Hardness Testing of Metallic Materials
• ASTM E466 Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials
• ASTM E467 Standard Practice for Verification of Constant Amplitude Dynamic Forces in an Axial Fatigue Testing System
• ASTM E468 Standard Practice for Presentation of Constant Amplitude Fatigue Test Results for Metallic Materials
• ASTM E6 Standard Terminology Relating to Methods of Mechanical Testing
• ASTM E606 Standard Practice for Strain-Controlled Fatigue Testing
• ASTM E647 Standard Test Method for Measurement of Fatigue Crack Growth Rates
• ASTM E7 Standard Terminology Relating to Metallography
• ASTM E740 Standard Practice for Fracture Testing with Surface-Crack Tension Specimens
• ASTM E8/E8M Standard Test Methods for Tension Testing of Metallic Materials
• ASTM E837 Standard Test Method for Determining Residual Stresses by the Hole-Drilling Strain-Gage Method
• ASTM E9 Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature
• ASTM E915 Standard Test Method for Verifying the Alignment of X-Ray Diffraction Instrumentation for Residual Stress Measurement
• ASTM F2792 Standard Terminology for Additive Manufacturing Technologies^,
• ASTM F2971 Standard Practice for Reporting Data for Test Specimens Prepared by Additive Manufacturing
• ISO 1099 Metallic materials - Fatigue testing - Axial force-controlled method
• ISO 1143 Metallic materials - Rotating bar bending fatigue testing
• ISO 11531 Metallic materials — Sheet and strip — Earing test
• ISO 12106 Metallic materials - Fatigue testing - Axial-strain-controlled method
• ISO 12108 Metallic materials - Fatigue testing - Fatigue crack growth method
• ISO 12111 Metallic materials - Fatigue testing - Strain-controlled thermomechanical fatigue testing method
• ISO 12135 Metallic materials - Unified method of test for the determination of quasistatic fracture toughness
• ISO 12737 Metallic materials — Determination of plane-strain fracture toughness
• ISO 1352 Metallic materials — Torque-controlled fatigue testing
• ISO 14556 Metallic materials — Charpy V-notch pendulum impact test — Instrumented test method
• ISO 148-3 Metallic materials - Charpy pendulum impact test - Part 3: Preparation and characterization of Charpy V-notch test pieces for indirect verification of pendulum impact machines
• ISO 15579 Metallic materials - Tensile testing at low temperature
• ISO 19819 Metallic materials - Tensile testing in liquid helium
• ISO 22889 Metallic materials.Method of test for the determination of resistance to stable crack extension using specimens of low constraint
• ISO 26203-1 Metallic materials - Tensile testing at high strain rates- Part 1:Elastic-bar-type systems
• ISO 26203-2 Metallic materials. Tensile testing at high rates of deformation. Part 2: Servohydraulics and other test systems Technical Corrigendum 1
• ISO 27306 Metallic materials - Method of constraint loss correction of CTOD fracture toughness for fracture assessment of steel components
• ISO 3369 Impermeable sintered metal materials and hardmetals - Determination of density
• ISO 3452-1 Non-destructive testing - Penetrant testing - Part 1: General principles
• ISO 377 Steel and steel products - Location and preparation of samples and test pieces for mechanical testing
• ISO 6892-1 Metallic materials — Tensile testing — Part 1: Method of test at room temperature
• ISO 6892-2 Metallic materials - Tensile testing- Part 2:Method of test at elevated temperature
• ISO/ASTM 52921 Standard terminology for additive manufacturing.Coordinate systems and test methodologies
• ISO/TR 14936 Metallic materials - Strain analysis report
• ISO/TR 29381 Metallic materials - Measurement of mechanical properties by an instrumented indentation test - Indentation tensile properties

ASTM F3122-14 history

• 2022 ASTM F3122-14(2022) Standard Guide for Evaluating Mechanical Properties of Metal Materials Made via Additive Manufacturing Processes
• 2014 ASTM F3122-14 Standard Guide for Evaluating Mechanical Properties of Metal Materials Made via Additive Manufacturing Processes