ASTM D6201-04(2014)
Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation
- Standard No.
- ASTM D6201-04(2014)
- Release Date
- 2004
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D6201-18
- Latest
- ASTM D6201-19a
- Scope
5.1 Test Method—The Coordinating Research Council sponsored testing to develop this test method to evaluate a fuel's tendency to form intake valve deposits.
5.1.1 State and Federal Legislative and Regulatory Action—Regulatory action by California Air Resources Board (CARB)9 and the United States Environmental Protection Agency (EPA)10 necessitate the acceptance of a standardized test method to evaluate the intake system deposit forming tendency of an automotive spark-ignition engine fuel.
5.1.2 Relevance of Results—The operating conditions and design of the engine used in this test method are not representative of all engines. These factors shall be considered when interpreting test results.
5.2 Test Validity:
5.2.1 Procedural Compliance—The test results are not considered valid unless the test is completed in compliance with all requirements of this test method. Deviations from the parameter limits presented in Sections 12 – 14 will result in an invalid test. Apply engineering judgment during conduct of the test method when assessing any anomalies to ensure validity of the test results.
5.2.2 Engine Compliance—A test is not considered valid unless the test engine meets the quality control inspection requirements as described in Sections 10 and 12.
1.1 This test method covers an engine dynamometer test procedure for evaluation of intake valve deposit formation of unleaded spark-ignition engine fuels.2 This test method uses a Ford Ranger 2.3 L four-cylinder engine. This test method includes detailed information regarding the procedure, hardware, and operations.
1.2 The ASTM Test Monitoring Center (TMC)3 is responsible for engine test stand calibration as well as issuance of information letters after test method modifications are approved by Subcommittee D02.A0 and Committee D02. Users of this test method shall request copies of recent information letters from the TMC to ensure proper conduct of the test method.
1.3 The values stated in SI units are to be regarded as standard. The values in parentheses are provided for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of th......
ASTM D6201-04(2014) Referenced Document
- ASTM D1266 Standard Test Method for Sulfur in Petroleum Products (Lamp Method)
- ASTM D1298 Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method
- ASTM D1319 Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption
- ASTM D1744 Standard Test Method for Determination of Water in Liquid Petroleum Products by Karl Fischer Reagent
- ASTM D235 Standard Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent)
- ASTM D2427 Standard Test Method for Determination of C2 through C5 Hydrocarbons in Gasolines by Gas Chromatography
- ASTM D2622 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
- ASTM D287 Standard Test Method for API Gravity of Crude Petroleum and Petroleum Products (Hydrometer Method)
- ASTM D3237 Standard Test Method for Lead In Gasoline By Atomic Absorption Spectroscopy
- ASTM D381 Standard Test Method for Existent Gum in Fuels by Jet Evaporation
- ASTM D4057 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
- ASTM D4294 Standard Test Method for Sulfur in Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectroscopy
- ASTM D4814 Standard Specification for Automotive Spark-Ignition Engine Fuel
- ASTM D4953 Standard Test Method for Vapor Pressure of Gasoline and Gasoline-Oxygenate Blends (Dry Method)
- ASTM D5059 Standard Test Methods for Lead in Gasoline by X-Ray Spectroscopy
- ASTM D5190 Standard Test Method for Vapor Pressure of Petroleum Products (Automatic Method)
- ASTM D5191 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method)
- ASTM D525 Standard Test Method for Oxidation Stability of Gasoline (Induction Period Method)
- ASTM D5302 Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation and Wear in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions
- ASTM D5482 Standard Test Method for Vapor Pressure of Petroleum Products (Mini Method-Atmospheric)
- ASTM D86 Standard Test Method for Distillation of Petroleum Products
- ASTM D873 Standard Test Method for Oxidation Stability of Aviation Fuels (Potential Residue Method)
- ASTM E1064 Standard Test Method for Water in Organic Liquids by Coulometric Karl Fischer Titration
- ASTM E203 Standard Test Method for Water Using Volumetric Karl Fischer Titration
ASTM D6201-04(2014) history
- 2019 ASTM D6201-19a Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation
- 2019 ASTM D6201-19 Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation
- 2018 ASTM D6201-18a Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation
- 2018 ASTM D6201-18 Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation
- 2004 ASTM D6201-04(2014) Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation
- 2004 ASTM D6201-04(2009) Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation
- 2004 ASTM D6201-04 Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation
- 2003 ASTM D6201-03 Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation
- 2001 ASTM D6201-01 Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation
- 2000 ASTM D6201-00 Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation
- 1999 ASTM D6201-99 Standard Test Method for Dynamometer Evaluation of Unleaded Spark-Ignition Engine Fuel for Intake Valve Deposit Formation
Copyright ©2024 All Rights Reserved