ASTM F2736-13e1
Standard Specification for 6 to 30 in. (152 To 762 mm) Polypropylene (PP) Corrugated Single Wall Pipe And Double Wall Pipe

Standard No.

ASTM F2736-13e1

Release Date

2013

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM F2736-13e1

Replace By

F3219

Scope

1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, elongation, brittleness, pipe stiffness, and markings for single wall corrugated polypropylene (PP) pipe and double wall corrugated polypropylene (PP) pipe. It covers nominal sizes 6 in. through 30 in. (152 mm through 762 mm).

1.2 The corrugated polypropylene pipes governed by this standard are intended for use in non-pressure applications for sanitary sewers, storm sewers and drainage pipes. Single wall corrugated polypropylene pipe shall not be used for sanitary sewer applications.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F2736-13e1 Referenced Document

• ASTM D1238 Standard Test Method for Flow Rates of Thermoplastics by Extrusion Plastometer
• ASTM D1505 Standard Test Method for Density of Plastics by the Density-Gradient Technique
• ASTM D1600 Standard Terminology for Abbreviated Terms Relating to Plastics
• ASTM D2122 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
• ASTM D2321 Recommended Practice for Underground Installation Of Flexible Thermoplastic Sewer Pipe
• ASTM D2412 Standard Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
• ASTM D2444 Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
• ASTM D256 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
• ASTM D2990 Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
• ASTM D3212 Standard Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
• ASTM D3895 Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry
• ASTM D4101 Standard Specification for Propylene Plastic Injection and Extrusion Materials
• ASTM D618 Standard Practice for Conditioning Plastics for Testing
• ASTM D638 Standard Test Method for Tensile Properties of Plastics
• ASTM D6992 Standard Test Method for Accelerated Tensile Creep and Creep-Rupture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped Isothermal Method
• ASTM D790 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials*， 2024-04-20 Update
• ASTM D792 Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
• ASTM F412 Standard Terminology Relating to Plastic Piping Systems
• ASTM F477 Standard Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe

ASTM F2736-13e1 history

• 2013 ASTM F2736-13e1 Standard Specification for 6 to 30 in. (152 To 762 mm) Polypropylene (PP) Corrugated Single Wall Pipe And Double Wall Pipe
• 2013 ASTM F2736-13 Standard Specification for 6 to 30 in. (152 To 762 mm) Polypropylene (PP) Corrugated Single Wall Pipe And Double Wall Pipe
• 2012 ASTM F2736-12 Standard Specification for 6 to 30 in. (152 To 762 mm) Polypropylene (PP) Corrugated Single Wall Pipe And Double Wall Pipe
• 2010 ASTM F2736-10 Standard Specification for 6 to 30 in. (152 To 762 mm) Polypropylene (PP) Corrugated Single Wall Pipe And Double Wall Pipe