ASTM F2924-14
Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium with Powder Bed Fusion

Standard No.

ASTM F2924-14

Release Date

2014

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM F2924-14(2021)

Latest

ASTM F2924-14(2021)

Scope

1.1 This specification covers additively manufactured titanium-6aluminum-4vanadium (Ti-6Al-4V) components using full-melt powder bed fusion such as electron beam melting and laser melting. The components produced by these processes are used typically in applications that require mechanical properties similar to machined forgings and wrought products. Components manufactured to this specification are often, but not necessarily, post processed via machining, grinding, electrical discharge machining (EDM), polishing, and so forth to achieve desired surface finish and critical dimensions.

1.2 This specification is intended for the use of purchasers or producers, or both, of additively manufactured Ti-6Al-4V components for defining the requirements and ensuring component properties.

1.3 Users are advised to use this specification as a basis for obtaining components that will meet the minimum acceptance requirements established and revised by consensus of the members of the committee.

1.4 User requirements considered more stringent may be met by the addition to the purchase order of one or more Supplementary Requirements, which may include, but are not limited to, those listed in S1-S16.

1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F2924-14 Referenced Document

• ASME B46.1 Surface Texture (Surface Roughness, Waviness, and Lay) ( - 2009)
• ASTM B213 Standard Test Method for Flow Rate of Metal Powders
• ASTM B214 Standard Test Method for Sieve Analysis of Metal Powders
• ASTM B243 Standard Terminology of Powder Metallurgy
• ASTM B311 Test Method for Density Determination for Powder Metallurgy (P/M) Materials Containing Less Than Two Percent Porosity
• ASTM B600 Standard Guide for Descaling and Cleaning Titanium and Titanium Alloy Surfaces
• ASTM B769 Standard Test Method for Shear Testing of Aluminum Alloys
• ASTM B964 Standard Test Methods for Flow Rate of Metal Powders Using the Carney Funnel
• ASTM D3951 Standard Practice for Commercial Packaging
• ASTM E10 Standard Test Method for Brinell Hardness of Metallic Materials
• ASTM E11 Standard Specification for Wire Cloth and Sieves for Testing Purposes
• ASTM E1409 Standard Test Method for Determination of Oxygen in Titanium and Titanium Alloys by the Inert Gas Fusion Technique
• ASTM E1417 Standard Practice for Liquid Penetrant Examination
• ASTM E1447 Standard Test Method for Determination of Hydrogen in Titanium and Titanium Alloys by the Inert Gas Fusion Thermal Conductivity Method
• ASTM E1450 Standard Test Method for Tension Testing of Structural Alloys in Liquid Helium
• ASTM E18 Standard Test Methods for Rockwell Hardness of Metallic Materials
• ASTM E1820 Standard Test Method for Measurement of Fracture Toughness
• ASTM E1941 Standard Test Method for Determination of Carbon in Refractory and Reactive Metals and Their Alloys
• ASTM E21 Standard Test Methods for Elevated Temperature Tension Tests of Metallic Materials
• ASTM E23 Standard Test Methods for Notched Bar Impact Testing of Metallic Materials
• ASTM E2368 Standard Practice for Strain Controlled Thermomechanical Fatigue Testing
• ASTM E2371 Standard Test Method for Analysis of Titanium and Titanium Alloys by Direct Current Plasma and Inductively Coupled Plasma Atomic Emission Spectrometry (Performance-Based Test Methodology)*， 2024-04-20 Update
• ASTM E238 Standard Test Method for Pin-Type Bearing Test of Metallic Materials
• ASTM E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
• ASTM E3 Standard Practice for Preparation of Metallographic Specimens
• ASTM E384 Standard Test Method for Microindentation Hardness of Materials
• ASTM E399 Standard Test Method for Plane-Strain Fracture Toughness of Metallic Materials
• ASTM E407 Standard Practice for Microetching Metals and Alloys
• ASTM E466 Standard Practice for Conducting Force Controlled Constant Amplitude Axial Fatigue Tests of Metallic Materials
• ASTM E539 Standard Test Method for X-Ray Emission Spectrometric Analysis of 6AI-4V Titanium Alloy
• ASTM E606 Standard Practice for Strain-Controlled Fatigue Testing
• ASTM E647 Standard Test Method for Measurement of Fatigue Crack Growth Rates
• ASTM E8/E8M Standard Test Methods for Tension Testing of Metallic Materials
• ASTM E9 Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature
• ASTM F1472 Standard Specification for Wrought Titanium -6Aluminum -4Vanadium Alloy (UNS R56400) for Surgical Implant Applications
• ASTM F2792 Standard Terminology for Additive Manufacturing Technologies^,
• ASTM F629 Standard Practice for Radiography of Cast Metallic Surgical Implants
• ISO 1099 Metallic materials - Fatigue testing - Axial force-controlled method
• ISO 12108 Metallic materials - Fatigue testing - Fatigue crack growth method
• ISO 12111 Metallic materials - Fatigue testing - Strain-controlled thermomechanical fatigue testing method
• ISO 12135 Metallic materials - Unified method of test for the determination of quasistatic fracture toughness
• ISO 12737 Metallic materials — Determination of plane-strain fracture toughness
• ISO 13485 
• ISO 148-1 Metallic materials - Charpy pendulum impact test - Part 1: Test method
• ISO 19819 Metallic materials - Tensile testing in liquid helium
• ISO 4545 Metallic materials; hardness test; Knoop test
• ISO 5832-3 Implants for surgery — Metallic materials — Part 3: Wrought titanium 6-aluminium 4-vanadium alloy
• ISO 6506-1 Metallic materials - Brinell hardness test - Part 1: Test method
• ISO 6507-1 Metallic materials — Vickers hardness test — Part 1: Test method
• ISO 6508 Metallic materials; Hardness test; Rockwell test (scales A - B - C - D - E - F - G - H - K)
• ISO 6892-1 Metallic materials — Tensile testing — Part 1: Method of test at room temperature
• ISO 6892-2 Metallic materials - Tensile testing- Part 2:Method of test at elevated temperature
• ISO 9001 Quality management systems - Requirements [Spanish version]
• ISO 9044 Industrial woven wire cloth - Technical requirements and tests

ASTM F2924-14 history

• 2021 ASTM F2924-14(2021) Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium with Powder Bed Fusion
• 2014 ASTM F2924-14 Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium with Powder Bed Fusion
• 2012 ASTM F2924-12a Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium with Powder Bed Fusion
• 2012 ASTM F2924-12 Standard Specification for Additive Manufacturing Titanium-6 Aluminum-4 Vanadium with Powder Bed Fusion