This European Standard specifies the minimum requirements for the design and construction of metallic pressure tanks having a maximum working or test pressure exceeding 50 kPa (0,5 bar), for the transport of dangerous goods by road and rail and sea. This European Standard includes requirements for openings, closures and structural equipment; it does not cover requirements of service equipment. For tanks for the transport of cryogenic liquids, EN 13530-1 and EN 13530-2 apply. NOTE 1 Design and construction of pressure tanks according to the scope of this European Standard are primarily subject to the requirements of RID/ADR, 6.8.2.1, 6.8.3.1 and 6.8.5, as relevant. In addition, the relevant requirements of RID/ADR, columns 12 and 13 of Table A to chapter 3.2, 4.3 and 6.8.2.4 apply. For the structural equipment subsections 6.8.2.2 and 6.8.3.2 apply, as relevant. The definitions of RID/ADR are referred to. For portable tanks see also Chapter 4.2 and Sections 6.7.2 and 6.7.3 of RID and ADR. In addition, the relevant requirements of RID/ADR, columns 10 and 11 of Table A to Chapter 3.2, 4.2, 6.7.2 and 6.7.3 apply. The paragraph numbers above relate to the 2013 issue of RID/ADR which are subject to regular revisions. This can lead to temporary non-compliances with EN 14025. It is important to know that requirements of RID/ADR take precedence over any clause of this standard. NOTE 2 This standard is applicable to liquefied gases including LPG, however for a dedicated LPG standard see EN 12493. If not otherwise specified, provisions which take up the whole width of the page apply to all kind of tanks. Provisions contained in a single column apply only to: road and rail pressure tanks according to RID/ADR chapter 6.8 (left-hand column); portable tanks according to RID/ADR chapter 6.7 (right-hand column).
EN 14025:2013 Referenced Document
EN 10204:2004 Metallic products - Types of inspection documents
EN 13094:2008 Tanks for the transport of dangerous goods - Metallic tanks with a working pressure not exceeding 0,5 bar - Design and construction Incorporating corrigenda November 2008 and November 2009
EN 13445-2:2009 Unfired pressure vessels - Part 2: Materials
EN 13445-4:2009 Unfired pressure vessels - Part 4: Fabrication
EN 13445-8:2009 Unfired pressure vessels - Part 8: Additional requirements for pressure vessels of aluminium and aluminium alloys
EN 1418:1997 Welding Personnel - Approval Testing of Welding Operators for Fusion Welding and Resistance Weld Setters for Fully Mechanized and Automatic Welding of Metallic Materials
EN 1435:1997 Non-destructive testing of welds Radiographic testing of welded joints Includes amendments A1:2002 and A2:2003
EN 1591-1:2001 Flanges and their joints - Design rules for gasketed circular flange connections - Part 1: Calculation method Incorporates Amendment A1: 2009
EN ISO 3834-1:2005 Quality requirements for fusion welding of metallic materials - Part 1: Criteria for the selection of the appropriate level of quality requirements (ISO 3834-1:2005)
EN ISO 3834-2:2005 Quality requirements for fusion welding of metallic materials - Part 2: Comprehensive quality requirements (ISO 3834-2:2005)
EN ISO 4136:2012 Destructive tests on welds in metallic materials - Transverse tensile test
EN ISO 5173:2010 Destructive tests on welds in metallic materials - Bend tests (Incorporates Amendment A1: 2011)
EN ISO 5817:2007 Welding - Fusion-welded joints in steel@ nickel@ titanium and their alloys (beam welding excluded) - Quality levels for imperfections
EN ISO 9606-2:2004 Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004)
EN 14025:2013 history
2023EN 14025:2023 Tanks for the transport of dangerous goods - Metallic pressure tanks - Design and construction
2020EN 14025:2018/AC:2020 Tanks for the transport of dangerous goods - Metallic pressure tanks - Design and construction
2018EN 14025:2018 Tanks for the transport of dangerous goods - Metallic pressure tanks - Design and construction
2013EN 14025:2013 Tanks for the transport of dangerous goods - Metallic pressure tanks - Design and construction
2008EN 14025:2008 Tanks for the transport of dangerous goods - Metallic pressure tanks - Design and Construction
2003EN 14025:2003 Tanks for the transport of dangerous goods Metallic pressure tanks Design and construction Incorporating corrigendum March 2005