This International Standard specifies basic requirements for the installation of media for communication networks in industrial premises and within and between the automation islands@ of industrial sites. This standard covers balanced and optical fibre cabling. It also covers the cabling infrastructure for wireless media@ but not the wireless media itself. Additional media are covered in the IEC 61784-5 series. This standard is a companion standard to the communication networks of the industrial automation islands and especially to the communication networks specified in the IEC 61158 series and the IEC 61784 series. In addition@ this standard covers: ? the installation of generic telecommunication cabling for industrial premises as specified in ISO/IEC 24702; ? the connection between the generic telecommunications cabling specified in ISO/IEC 24702 and the specific communication cabling of an automation island@ where an automation outlet (AO) replaces the telecommunication outlet (TO) of ISO/IEC 24702. NOTE If the interface used at the AO does not conform to that specified for the TO of ISO/IEC 24702@ the cabling no longer conforms to ISO/IEC 24702 although certain features@ including performance@ of generic cabling may be retained. This standard provides guidelines that cope with the critical aspects of the industrial automation area (safety@ security and environmental aspects such as mechanical@ liquid@ particulate@ climatic@ chemicals and electromagnetic interference). This standard does not recognise implementations of power distribution through Ethernet balanced cabling systems that are not specified in IEEE 802.3 and in IEEE 802.3at. This standard deals with the roles of planner@ installer@ verifier@ and acceptance test personnel@ administration and maintenance personnel and specifies the relevant responsibilities and/or gives guidance.
IEC 61918:2013 Referenced Document
EN 50310:2010 Application of equipotential bonding and earthing in buildings with information technology equipment*， 2024-04-20 Update
IEC 60364-1:2005 Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions
IEC 60364-4-41:2005 Low-voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock
IEC 60364-4-44:2007 Low-voltage electrical installations - Part 4-44: Protection for safety - Protection against voltage disturbances and electromagnetic disturbances
IEC 60364-5-54:2011 Low-voltage electrical installations - Part 5-54: Selection and erection of electrical equipment - Earthing arrangements and protective conductors
IEC 60529:1989 Degrees of protection provided by enclosures (IP code)
IEC 60603-1:1991 Connectors for frequencies below 3 MHz for use with printed boards; part 1: generic specification; general requirements and guide for the preparation of detail specifications, with assessed quality
IEC 60603-2:1995 Connectors for frequencies below 3 MHz for use with printed boards - Part 2: Detail specification for two-part connectors with assessed quality, for printed boards, for basic grid of 2,54 mm (0,1 in) with common mounting features
IEC 60603-3:1987 Connectors for frequencies below 3 MHz for use with printed boards. Part 3 : Two-part connectors for printed boards having contacts spaced 2.54 mm (O.100 in) centres and staggered terminations at that same spacing
IEC 60603-4:1987 Connectors for frequencies below 3 MHz for use with printed boards. Part 4 : Two-part connectors for printed boards having contacts spaced at 1.91 mm (0.075 in) centres and staggered terminations at that same spacing
IEC 60603-5:1987 Connectors for frequencies below 3 MHz for use with printed boards. Part 5 : Edge-socket connectors and two-part connectors for double-sided printed boards with 2.54 mm (O.1 in) spacing
IEC 60603-6:1987 Connectors for frequencies below 3 MHz for use with printed boards. Part 6: Edge-socket connectors and printed board connectors with 2.54 mm (0.1 in) contact spacing for single or double-sided printed boards of 1.6 mm (0.063 in) nominal thickness.
IEC 60603-7-1:2011 Connectors for electronic equipment - Part 7-1: Detail specification for 8-way, shielded, free and fixed connectors
IEC 60603-7-2:2010 Connectors for electronic equipment - Part 7-2: Detail specification for 8-way, unshielded, free and fixed connectors, for data transmission with frequencies up to 100 MHz
IEC 60603-7-3:2010 Connectors for electronic equipment - Part 7-3: Detail specification for 8-way, shielded, free and fixed connectors, for data transmission with frequencies up to 100 MHz
IEC 60603-7-41:2010 Connectors for electronic equipment - Part 7-41: Detail specification for 8-way, unshielded, free and fixed connectors, for data transmissions with frequencies up to 500 MHz
IEC 60603-7-4:2010 Connectors for electronic equipment - Part 7-4: Detail specification for 8-way, unshielded, free and fixed connectors, for data transmission with frequencies up to 250 MHz
IEC 60603-7-5:2010 Connectors for electronic equipment - Part 7-5: Detail specification for 8-way, shielded, free and fixed connectors, for data transmission with frequencies up to 250 MHz
IEC 60603-7-7:2010 Connectors for electronic equipment - Part 7-7: Detail specification for 8-way, shielded, free and fixed connectors, for data transmissions with frequencies up to 600 MHz
IEC 60603-7:2008 Connectors for electronic equipment - Part 7: Detail specification for 8-way, unshielded, free and fixed connectors