EN 16245-2:2013 Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 2: Specific requirements for resin@ curing systems@ additives and modifiers
This European Standard specifies the minimum information to be declared for resins, curing systems, additives and modifiers to be used for the manufacturing of composites products. These specific declaration requirements are in addition to the general requirements given in EN 16245-1. This document includes requirements for the Certificate of Analysis (CoA). The purpose of the CoA is to verify that material properties and quality conforms to the declared values.
EN 16245-2:2013 Referenced Document
ASTM D2196-10 Standard Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational (Brookfield type) Viscometer*, 2024-04-20 Update
ASTM D4835-08 Standard Specification for Propylene Glycol Monomethyl Ether Acetate*, 2024-04-20 Update
ASTM D6420-99 Standard Test Method for Determination of Gaseous Organic Compounds by Direct Interface Gas Chromatography-Mass Spectrometry
ASTM E1473-09 Standard Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys*, 2024-04-20 Update
ASTM E298-08 Standard Test Methods for Assay of Organic Peroxides*, 2024-04-20 Update
DIN 16945:1989 Testing of resins, hardeners and accelerators, and catalyzed resins
EN 16245-1:2013 Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 1: General requirements
EN 59:1977 Glass Reinforced Plastics: Measurement of Hardness by Means of a Barcol Impressor
EN ISO 1183-1:2012 Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012)*, 2024-04-20 Update
EN ISO 1183-2:2004 Plastics - Methods for determining the density of non-cellular plastics - Part 2: Density gradient column method (ISO 1183-2:2004)
EN ISO 1183-3:1999 Plastics - Methods for Determining the Density of Non-Cellular Plastics - Part 3: Gas Pyknometer Method ISO 1183-3:1999
EN ISO 178:2010 Plastics - Determination of flexural properties (ISO 178:2010)*, 2024-04-20 Update
EN ISO 2114:2000 Plastics (Polyester Resins) and Paints and Varnishes (Binders) - Determination of Partial Acid Value and Total Acid Value ISO 2114: 2000
EN ISO 2555:1999 Plastics - Resins in the Liquid State or as Emulsions or Dispersions - Determination of Apparent Viscosity by the Brookfield Test Method
EN ISO 2592:2001 Determination of Flash and Fire Points - Cleveland Open Cup Method [Use: IP 36/2002]
EN ISO 2719:2002 Determination of flash point - Pensky-Martens closed cup method Supersedes EN 22719:1993; [Use: IP 34/03]*, 2024-04-20 Update
EN ISO 291:2008 Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008)
EN ISO 527-1:2012 Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012)
EN ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
EN ISO 527-3:1995 Plastics - Determination of Tensile Properties - Part 3: Test Conditions for Films and Sheets ISO 527-3: 1995; Incorporating Technical corrigenda June 1998 and April 2001
EN ISO 527-4:1997 Plastics - Determination of Tensile Properties - Part 4: Test Conditions for Isotropic and Orthotropic Fibre-Reinforced Plastic Composites ISO 527-4: 1997
EN ISO 527-5:2009 Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites
EN ISO 584:1997 Plastics - Unsaturated Polyester Resins - Determination of Reactivity at 80 Degrees Celsius (Conventional Method) ISO 584: 1982
EN ISO 62:2008 Plastics - Determination of water absorption (ISO 62:2008)
EN ISO 75-2:2013 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite
EN ISO 787-5:1995 General Methods of Test for Pigments and Extenders - Part 5: Determination of Oil Absorption Value (ISO 787-5 : 1980)
EN 16245-2:2013 history
2013EN 16245-2:2013 Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 2: Specific requirements for resin@ curing systems@ additives and modifiers