ASTM F2145-13
Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing
- Standard No.
- ASTM F2145-13
- Release Date
- 2013
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM F2145-13(2018)
- Latest
- ASTM F2145-23
- Scope
1.1 This specification describes requirements and test methods for the qualification of Polyamide 11 (PA 11) bodied mechanical fittings for use with outside diameter controlled Polyamide 11 (PA 11), nominal 2 pipe size (IPS), and smaller complying with Specification D2513. Additionally, the requirements and test methods for the qualification of Polyamide 12 (PA12) bodied mechanical fittings for use with outside diameter controlled Polyamide 11 (PA11) nominal 2 in pipe size (IPS) and smaller complying with Specification D2513 and outside diameter controlled Polyamide 12 (PA12) nominal 2 in pipe size (IPS) and smaller complying with Specification F2785. In addition, it specifies general requirements of the material from which these fittings are made.
1.2 The test methods described in this specification are not intended to be used as routine quality tests.
1.3 This specification covers the types of mechanical fittings covered in 3.2.1.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
ASTM F2145-13 Referenced Document
- ASME B31.8 Gas Transmission and Distribution Piping Systems
- ASTM D1598 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
- ASTM D1600 Standard Terminology for Abbreviated Terms Relating to Plastics
- ASTM D2513 Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings
- ASTM D2837 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
- ASTM D638 Standard Test Method for Tensile Properties of Plastics
- ASTM F1588 Standard Test Method for Constant Tensile Load Joint Test (CTLJT)
- ASTM F2785 Standard Specification for Polyamide 12 Gas Pressure Pipe, Tubing, and Fittings
- ASTM F2945 Standard Specification for Polyamide 11 Gas Pressure Pipe, Tubing, and Fittings
- ASTM F412 Standard Terminology Relating to Plastic Piping Systems
ASTM F2145-13 history
- 2023 ASTM F2145-23 Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing
- 2018 ASTM F2145-13(2018) Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing
- 2013 ASTM F2145-13 Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing
- 2009 ASTM F2145-09 Standard Specification for Polyamide 11 (PA 11) and Polyamide 12 (PA12) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 and Polyamide 12 Pipe and Tubing
- 2001 ASTM F2145-01(2007) Standard Specification for Polyamide 11 (PA 11) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 Pipe and Tubing
- 2001 ASTM F2145-01 Standard Specification for Polyamide 11 (PA 11) Mechanical Fittings for Use on Outside Diameter Controlled Polyamide 11 Pipe and Tubing
