ASTM D7167-12
Standard Guide for Establishing Procedures to Monitor the Performance of Safety-Related Coating Service Level III Lining Systems in an Operating Nuclear Power Plant

Standard No.

ASTM D7167-12

Release Date

2012

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM D7167-12(2018)

Latest

ASTM D7167-12(2018)

Scope

4.1 Establishment of an in-service linings monitoring program permits planning and prioritization of lining maintenance work as needed to maintain lining integrity and performance in nuclear Coating Service Level III systems. Refer to ASTM MNL-8, Manual on Maintenance Coatings for Nuclear Power Plants,⁷ and Guide D7230, which provides guidance for selecting lining materials for new construction or maintenance of safety-related lining systems.

4.2 A linings monitoring program enables early identification and detection of potential problems in lining systems. Some Coating Service Level III lining systems may be known in advance to be suspect, deficient, or degraded. Monitoring lining performance will assist in developing follow-up procedures to resolve any significant deficiency relative to lining work.

4.3 Degraded linings may generate debris under normal operation and testing or during upset conditions that could adversely affect the performance of safety-related systems. In most cases, the consequence of the debris generation is flow blockage, essential heat transfer reduction, or both; ultimately leading to degradation of equipment or system performance. A linings monitoring program may be required to fulfill licensing commitments for Coating Service Level III lining work.

1.1 This guide covers procedures for establishing a program to monitor the performance of Coating Service Level III lining (and coating) systems in operating nuclear power plants. Monitoring is an ongoing process of evaluating the condition of the in-service lining systems.

1.2 Coating Service Level III lining systems subject to this guide are generally those applied to metal substrates comprising raw water, condensate-quality water, or fuel oil wetted (that is, full or intermittent immersion) surfaces in systems that may include:

1.2.1 Service water piping upstream of safety-related components,

1.2.2 Service water pump internals (draft tube, volutes, and diffusers),

1.2.3 Service water heat exchangers including the channels, pass partitions, tubesheets, end bells, and covers

1.2.4 Service water strainers,

1.2.5 Reactor water storage tanks (RWSTs),

1.2.6 Refuel cavity water storage tanks,

1.2.7 Reactor makeup water system,

1.2.8 Component cooling water system,

1.2.9 Lube oil tanks for safety-related equipment, and

1.2.10 Emergency diesel fuel oil system.

1.3 It is the intent of this guide to provide a reco......

ASTM D7167-12 Referenced Document

• ANSI/ASME NQA-1 Quality Assurance Requirements for Nuclear Facility Applications
• ASTM D1186 Standard Test Methods for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to a Ferrous Base
• ASTM D1400 Standard Test Method for Nondestructive Measurement of Dry Film Thickness of Nonconductive Coatings Applied to a Nonferrous Metal Base
• ASTM D3359 Standard Test Methods for Measuring Adhesion by Tape Test
• ASTM D4537 Standard Guide for Establishing Procedures to Qualify and Certify Inspection Personnel for Coating Work in Nuclear Facilities
• ASTM D4538 Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities
• ASTM D4541 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
• ASTM D610 Standard Test Method for Evaluating Degree of Rusting on Painted Steel Surfaces
• ASTM D6677 Standard Test Method for Evaluating Adhesion by Knife
• ASTM D7108 Standard Guide for Establishing Qualifications for a Nuclear Coatings Specialist
• ASTM D714 Standard Test Method for Evaluating Degree of Blistering of Paints
• ASTM D7230 Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates*， 2024-04-20 Update
• ASTM F1130 Standard Practice for Inspecting the Coating System of a Ship

ASTM D7167-12 history

• 2018 ASTM D7167-12(2018) Standard Guide for Establishing Procedures to Monitor the Performance of Safety-Related Coating Service Level III Lining Systems in an Operating Nuclear Power Plant
• 2012 ASTM D7167-12 Standard Guide for Establishing Procedures to Monitor the Performance of Safety-Related Coating Service Level III Lining Systems in an Operating Nuclear Power Plant
• 2005 ASTM D7167-05 Standard Guide for Establishing Procedures to Monitor the Performance of Safety-Related Coating Service Level III Lining Systems in an Operating Nuclear Power Plant