ASTM B746/B746M-02(2012)
Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches
- Standard No.
- ASTM B746/B746M-02(2012)
- Release Date
- 2002
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM B746/B746M-16
- Latest
- ASTM B746/B746M-22e1
- Scope
1.1 This specification covers corrugated aluminum alloy structural plate used in the construction of pipe, pipe-arches, arches, underpasses, box culverts, and special shapes for field assembly. Appropriate fasteners are also described. The pipe, arches, and other shapes are generally used for drainage purposes, pedestrian and vehicular underpasses, and utility tunnels. Aluminum box culvert shapes are covered in Specification B864/B864M.
1.2 This specification does not include requirements for bedding, backfill, or the relationship between earth cover load and plate thickness of the pipe. Experience has shown that the successful performance of this product depends upon the proper selection of plate thickness, type of bedding and backfill, controlled manufacture in the plant, and care in the installation. The purchaser must correlate the above factors and also the corrosion and abrasion requirements of the field installation with the plate thickness. The structural design of corrugated aluminum structural plate pipe and the proper installation procedures are given in Practices B790/B790M and B789/B789M, respectively. A procedure for using life-cycle cost analysis techniques to evaluate alternate drainage system designs using corrugated metal pipe is given in Practice A930.
1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other.
ASTM B746/B746M-02(2012) Referenced Document
- ASTM A153/A153M Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware
- ASTM A307 Standard Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strangth
- ASTM A325 Standard Specification for High-Strength Bolts For Structural Steel Joints
- ASTM A449 Standard Specification for Quenched And Tempered Steel Bolts And Studs
- ASTM A563 Standard Specification for Carbon and Alloy Steel Nuts*， 2024-04-19 Update
- ASTM A563M Standard Specification for Carbon and Alloy Steel Nuts 40;Metric41;*， 2024-04-19 Update
- ASTM A930 Standard Practice for Life-Cycle Cost Analysis of Corrugated Metal Pipe Used for Culverts, Storm Sewers, and Other Buried Conduits
- ASTM B209 Standard Specification for Aluminum and Aluminum- Alloy Sheet and Plate
- ASTM B209M Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate (Metric)*， 2024-04-19 Update
- ASTM B221 Standard Specification for Aluminum-Alloy Extruded Bars, Rods, Wire, Shapes, and Tubes
- ASTM B221M Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes (Metric)
- ASTM B666/B666M Standard Practice for Identification Marking of Aluminum and Magnesium Products
- ASTM B695 Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
- ASTM B789/B789M Standard Practice for Installing Corrugated Aluminum Structural Plate Pipe for Culverts and Sewers
- ASTM B790/B790M Standard Practice for Structural Design of Corrugated Aluminum Pipe, Pipe-Arches, and Arches for Culverts, Storm Sewers, and Other Buried Conduits
- ASTM B864/B864M Standard Specification for Corrugated Aluminum Box Culverts
- ASTM E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
- ASTM F467 Standard Specification for Nonferrous Nuts for General Use
- ASTM F467M Standard Specification for Nonferrous Nuts for General Use [Metric]
- ASTM F468 Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use
- ASTM F468M Standard Specification for Nonferrous Bolts, Hex Cap Screws, and Studs for General Use [Metric]
- ASTM F568M Standard Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners
- ASTM F593 Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
- ASTM F594 Standard Specification for Stainless Steel Nuts
- ASTM F738M Standard Specification for Stainless Steel Metric Bolts, Screws, and Studs
- ASTM F836M Standard Specification for Style 1 Stainless Steel Metric Nuts
ASTM B746/B746M-02(2012) history
- 2022 ASTM B746/B746M-22e1 Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches
- 2022 ASTM B746/B746M-22 Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches
- 2016 ASTM B746/B746M-16 Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches
- 2002 ASTM B746/B746M-02(2012) Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches
- 2002 ASTM B746/B746M-02(2007) Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches
- 2002 ASTM B746/B746M-02 Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches
- 2001 ASTM B746/B746M-01 Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches
- 1995 ASTM B746/B746M-95(2000) Standard Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches
