ASTM D4223/D4223M-12
Standard Practice for Preparation of Test Specimens of Asphalt-Stabilized Soils
- Standard No.
- ASTM D4223/D4223M-12
- Release Date
- 2012
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D4223/D4223M-20
- Latest
- ASTM D4223/D4223M-20
- Scope
This practice is intended for the preparation of standard specimens of soil-asphalt mixtures suitable for tests of Test Methods , D1560, D1561, D4123, and other tests using specimens of the above dimensions. This practice is limited to only fine-grained soils as defined in 6.1.
Note 18212;The quality of the results produced by this practice is dependent on the competence of the personnel performing it and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing, sampling, inspection, and so forth. Users of this practice are cautioned that compliance with Practice D3740 does not in itself ensure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors.
1.1 This practice covers the selection and proportioning of soils and emulsified or cutback asphalts and the fabrication of 100-mm [4-in.] diameter by 65-mm [2.5-in.] high test specimens.
1.2 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.
1.3 Units8212;The values stated in either SI units or inch-pound units [presented in brackets] are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3.1 The gravitational system of inch-pound units is used when dealing with inch-pound units. In this system, the pound (lbf) represents a unit of force (weight) while the unit for mass is slugs. The rationalized slug unit is not given, unless dynamic (F=ma) calculations are involved.
1.3.2 It is common practice in the engineering/construction profession to concurrently use pounds to represent both a unit of mass (lbm) and of force (lbf). This implicitly combines two separate systems of units; that is, the absolute system and the gravitational system. It is scientifically undesirable to combine the use of two separate sets of inch-pound units within a single standard. As stated, this standard includes the gravitational system of inch-pound units and does not use/present the slug unit for mass. However, the use of balances or scales recording pounds of mass (lbm) or recording in lbm/ft3 shall not be regarded as nonconformance with this standard.
1.4 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project''s many unique aspects. Th......
ASTM D4223/D4223M-12 Referenced Document
- ASTM C117 Standard Test Method for Materials Finer than 75-181m (No. 200) Sieve in Mineral Aggregates by Washing
- ASTM C136 Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates
- ASTM D1074 Standard Test Method for Compressive Strength of Bituminous Mixtures
- ASTM D1188 Standard Test Method for Bulk Specific Gravity and Density of Compacted Bituminous Mixtures Using Paraffin-Coated Specimens
- ASTM D1559 Test Method for Resistance of Plastic Flow of Bituminous Mixtures Using Marshall Apparatus
- ASTM D1560 Standard Test Methods for Resistance to Deformation and Cohesion of Bituminous Mixtures by Means of Hveem Apparatus
- ASTM D1561 Standard Practice for Preparation of Bituminous Mixture Test Specimens by Means of California Kneading Compactor
- ASTM D2026 Standard Specification for Cutback Asphalt (Slow-Curing Type)
- ASTM D2027 Standard Specification for Cutback Asphalt (Medium-Curing Type)
- ASTM D2028 Standard Specification for Cutback Asphalt (Rapid-Curing Type)
- ASTM D2216 Standard Test Method for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
- ASTM D2397 Standard Specification for Cationic Emulsified Asphalt
- ASTM D2419 Standard Test Method for Sand Equivalent Value of Soils and Fine Aggregate
- ASTM D2726 Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures
- ASTM D3740 Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
- ASTM D4123 Standard Test Method for Indirect Tension Test for Resilient Modulus of Bituminous Mixtures
- ASTM D4318 Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils
- ASTM D6026 Standard Practice for Using Significant Digits in Geotechnical Data
- ASTM D653 Standard Terminology Relating to Soil, Rock, and Contained Fluids
- ASTM D75 Standard Practice for Sampling Aggregates
- ASTM D8 Standard Terminology Relating to Materials for Roads and Pavements
- ASTM D977 Standard Specification for Emulsified Asphalt
ASTM D4223/D4223M-12 history
- 2020 ASTM D4223/D4223M-20 Standard Practices for Preparation of Test Specimens of Asphalt-Stabilized Soils
- 2012 ASTM D4223/D4223M-12 Standard Practice for Preparation of Test Specimens of Asphalt-Stabilized Soils
- 1999 ASTM D4223-99(2006) Standard Practice for Preparation of Test Specimens of Asphalt-Stabilized Soils
- 1999 ASTM D4223-99 Standard Practice for Preparation of Test Specimens of Asphalt-Stabilized Soils
