ASTM D6041-11
Standard Specification for Contact-Molded x201C;Fiberglassx201D; (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings
- Standard No.
- ASTM D6041-11
- Release Date
- 2011
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D6041-18
- Latest
- ASTM D6041-23
- Scope
1.1 This specification covers pipe and fittings fabricated by contact molding, for pressures to 150 psi and made of a commercial-grade polyester resin. Included are requirements for materials, properties, design, construction, dimensions, tolerances, workmanship, and appearance.
1.2 This specification does not cover resins other than polyester, reinforcing materials other than glass fibers or fabrication methods other than contact molding.
Note 18212;For the purposes of this specification, the term polyester resin will include both polyester and vinylester resins.
1.3 This specification does not cover the design of pipe and fittings intended for use with liquids heated above their flash points.
1.4 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are provided for information purposes only.
1.5 The following precautionary caveat pertains only to Section 10, the test methods portion, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 28212;There is no known ISO equivalent to this standard.
ASTM D6041-11 Referenced Document
- ASTM C581 Standard Practice for Determining Chemical Resistance of Thermosetting Resins Used in Glass-Fiber-Reinforced Structures Intended for Liquid Service
- ASTM C582 Standard Specification for Contact-Molded Reinforced Thermosetting Plastic (RTP) Laminates for Corrosion-Resistant Equipment
- ASTM D1599 Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings
- ASTM D1600 Standard Terminology for Abbreviated Terms Relating to Plastics
- ASTM D2583 Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor
- ASTM D2584 Standard Test Method for Ignition Loss of Cured Reinforced Resins
- ASTM D3567 Standard Practice for Determining Dimensions of ldquo;Fiberglassrdquo; (Glass-Fiber-Reinforced Thermosetting Resin) Pipe and Fittings
- ASTM D3681 Standard Test Method for Chemical Resistance of "Fiberglass" (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe in a Deflected Condition
- ASTM D5421 Standard Specification for Contact Molded "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Flanges
- ASTM D618 Standard Practice for Conditioning Plastics for Testing
- ASTM D638 Standard Test Method for Tensile Properties of Plastics
- ASTM D883 Standard Terminology Relating to Plastics
- ASTM F412 Standard Terminology Relating to Plastic Piping Systems
ASTM D6041-11 history
- 2023 ASTM D6041-23 Standard Specification for Contact-Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings
- 2018 ASTM D6041-18 Standard Specification for Contact-Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings
- 2011 ASTM D6041-11 Standard Specification for Contact-Molded x201C;Fiberglassx201D; (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings
- 1997 ASTM D6041-97(2002) Standard Specification for Contact-Molded "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings
- 1997 ASTM D6041-97 Standard Specification for Contact-Molded "Fiberglass" (Glass-Fiber-Reinforced Thermosetting Resin) Corrosion Resistant Pipe and Fittings
