International Organization for Standardization (ISO)
Latest
ISO 23559:2011
Scope
This International Standard identifies specific test procedures to assist producers and users in the selection and characterization of thermoplastic films in single- or multi-layer form. It is intended to serve as a guide for those films for which there are no existing standards or specifications.
NOTE Because of the range of materials used and the wide variety of processes available to produce various film constructions, this document does not address specimen preparation.
If an International Standard exists for a specific film product, the requirements of that standard shall take precedence over this document.
There are many national, regional and industrial standards that address the requirements for specific applications. Since this International Standard is intended to provide general guidance, it is not within the scope to address these.
The significance of the data and fitness for use shall be determined by the user.
ISO 23559:2011 Referenced Document
IEC 60093 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
IEC 60112 Method for the determination of the proof and the comparative tracking indices of solid insulating materials*, 2020-10-28 Update
IEC 60243-1 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies*, 2013-03-01 Update
IEC 60250 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including meter wavelengths
ISO 1133-1 Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics — Part 1: Standard method*, 2022-06-23 Update
ISO 11357-2 Plastics — Differential scanning calorimetry (DSC) — Part 2: Determination of glass transition temperature and step height*, 2020-03-02 Update
ISO 11357-3 Plastics - Differential scanning calorimetry (DSC) - Part 3: Determination of temperature and enthalpy of melting and crystallization*, 2018-03-01 Update
ISO 11443 Plastics - Determination of the fluidity of plastics using capillary and slit-die rheometers*, 2021-01-31 Update
ISO 11501 Plastics - Film and sheeting - Determination of dimensional change on heating
ISO 11502 Plastics — Film and sheeting — Determination of blocking resistance*, 2018-11-02 Update
ISO 1183-1 Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pycnometer method and titration method*, 2019-02-28 Update
ISO 1183-2 Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient column method*, 2019-02-28 Update
ISO 1183-3 Plastics - Methods for determining the density of non-cellular plastics - Part 3: Gas pyknometer method
ISO 13468-1 Plastics — Determination of the total luminous transmittance of transparent materials — Part 1: Single-beam instrument*, 2019-06-05 Update
ISO 13468-2 Plastics — Determination of the total luminous transmittance of transparent materials — Part 2: Double-beam instrument*, 2021-06-04 Update
ISO 14782 Plastics — Determination of haze for transparent materials*, 2021-10-14 Update
ISO 15105-1 Plastics - Film and sheeting - Determination of gas-transmission rate - Part 1: Differential-pressure methods
ISO 15105-2 Plastics - Film and sheeting - Determination of gas transmission rate - Part 2: Equal-pressure method
ISO 15106-1 Plastics; Film and sheeting - Determination of water vapour transmission rate - Part 1: Humidity detection sensor method
ISO 15106-2 Plastics; Film and sheeting - Determination of water vapour transmission rate - Part 2: Infrared detection sensor method
ISO 15106-3 Plastics; Film and sheeting - Determination of water vapour transmission rate - Part 3: Electrolytic detection sensor method
ISO 15989 Plastics - Film and sheeting - Measurement of water-contact angle of corona-treated films; Technical Corrigendum 1
ISO 2813 Paints and varnishes - Determination of gloss value at 20 degrees, 60 degrees and 85 degrees*, 2014-10-01 Update
ISO 307 Plastics — Polyamides — Determination of viscosity number*, 2019-04-26 Update
ISO 4589-1 Plastics - Determination of burning behaviour by oxygen index - Part 1: General requirements*, 2017-04-01 Update
ISO 4589-2 Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test*, 2017-04-01 Update
ISO 4592 Plastics; film and sheeting; determination of length and width
ISO 4593 Plastics; film and sheeting; determination of thickness by mechanical scanning
ISO 527-3 Plastics — Determination of tensile properties — Part 3: Test conditions for films and sheets*, 2018-11-05 Update
ISO 6383-1 Plastics - Film and sheeting - Determination of tear resistance - Part 1: Trouser tear method*, 2015-12-01 Update
ISO 6383-2 Plastics; Film and sheeting; Determination of tear resistance; Part 2 : Elmendorf method
ISO 7765-1 Plastics film and sheeting; determination of impact resistance by the free-falling dart method; part 1: staircase methods
ISO 7765-2 Plastics film and sheeting — Determination of impact resistance by the free-falling dart method — Part 2: Instrumented puncture test*, 2022-05-20 Update
ISO 8295 Plastics - Film and sheeting - Determination of the coefficients of friction
ISO 8296 Plastics - Film and sheeting - Determination of wetting tension
ISO 9773 Plastics — Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source AMENDMENT 1: Specimens
ISO 23559:2011 history
2011ISO 23559:2011 Plastics - Film and sheeting - Guidance on the testing of thermoplastic films
2007ISO 23559:2007 Plastics - Film and sheeting - Guidance on the testing of thermoplastic films