ISO 10350-2:2011
Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics

Standard No.

ISO 10350-2:2011

Release Date

2011

Published By

International Organization for Standardization (ISO)

Status

Be replaced

Replace By

ISO 10350-2:2020

Latest

ISO 10350-2:2020

Scope

ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions or along different directions in the material. The properties included are those presented conventionally in manufacturers' data sheets. This part of ISO 10350 applies to reinforced thermoplastic and thermosetting materials where the reinforcement fibres are either discontinuous with a fibre length prior to processing greater than 7,5 mm or continuous (e.g. fabric, continuous-strand mat or unidirectional). Part 1 of this International Standard deals specifically with unreinforced and filled plastics, including those using fibres less than 7,5 mm in length.

ISO 10350-2:2011 Referenced Document

• IEC 60093 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
• IEC 60112 Method for the determination of the proof and the comparative tracking indices of solid insulating materials*， 2020-10-28 Update
• IEC 60243-1 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies*， 2013-03-01 Update
• IEC 60250 Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including meter wavelengths
• IEC 60296 Fluids for electrotechnical applications – Mineral insulating oils for electrical equipment*， 2020-06-26 Update
• ISO 11357-2 Plastics — Differential scanning calorimetry (DSC) — Part 2: Determination of glass transition temperature and step height*， 2020-03-02 Update
• ISO 11357-3 Plastics - Differential scanning calorimetry (DSC) - Part 3: Determination of temperature and enthalpy of melting and crystallization*， 2018-03-01 Update
• ISO 1172 Textile-glass-reinforced plastics — Prepregs, moulding compounds and laminates — Determination of the textile-glass and mineral-filler content using calcination methods*， 2023-08-01 Update
• ISO 14125:1998 Fibre-reinforced plastic composites - Determination of flexural properties
• ISO 14127 Carbon-fibre-reinforced composites - Determination of the resin, fibre and void contents
• ISO 14130 Fibre-reinforced plastic composites - Determination of apparent interlaminar shear strength by short-beam method; Technical Corrigendum 1
• ISO 15310 Fibre-reinforced plastic composites - Determination of the in-plane shear modulus by the plate twist method
• ISO 179-1 Plastics. Determination of Charpy impact properties - Non-instrumented impact test*， 2023-06-07 Update
• ISO 179-2 Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test — Amendment 1: Precision data*， 2020-05-14 Update
• ISO 2577 Plastics - Thermosetting moulding materials - Determination of shrinkage
• ISO 2818 Plastics — Preparation of test specimens by machining*， 2018-12-13 Update
• ISO 291 Plastics - Standard atmospheres for conditioning and testing
• ISO 4589-2 Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test*， 2017-04-01 Update
• ISO 527-4 Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites*， 2023-03-24 Update
• ISO 527-5 Plastics — Determination of tensile properties — Part 5: Test conditions for unidirectional fibre-reinforced plastic composites*， 2021-11-24 Update
• ISO 62 Plastics - Determination of water absorption
• ISO 6603-2 Plastics. Determination of puncture impact behaviour of rigid plastics. - Part 2: Instrumented impact testing*， 2023-06-02 Update
• ISO 75-3 Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
• ISO 7822 Textile glass reinforced plastics; determination of void content; loss on ignition, mechanical disintegration and statistical counting methods

ISO 10350-2:2011 history

• 2020 ISO 10350-2:2020 Plastics — Acquisition and presentation of comparable single-point data — Part 2: Long-fibre-reinforced plastics
• 2011 ISO 10350-2:2011 Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics
• 2001 ISO 10350-2:2001 Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics