DIN 4040-100:2004
Grease separators - Part 100: Requirements relating to the use of separators to DIN EN 1825-1 and DIN EN 1825-2

Standard No.

DIN 4040-100:2004

Release Date

2004

Published By

German Institute for Standardization

Status

Be replaced

Replace By

DIN 4040-100:2016

DIN 4040-100 E:2014

Latest

DIN 4040-100:2016-12

Replace

DIN 4040-100:2002 DIN V 4040-2:1999 DIN 4040-1:1989

Scope

This standard specifies requirements for and methods of testing grease separators*) ('separators', for short) of the type specified in DIN EN 1825-1 and DIN EN 1825-2. It is to be used only in conjunction with the latter documents.

DIN 4040-100:2004 Referenced Document

• DIN 18381 German construction contract procedures (VOB) - Part C: General technical specifications in construction contracts (ATV) - Installation of gas, water and drainage pipework inside buildings*， 2019-09-01 Update
• DIN 1986-100:2002 Drainage systems on private ground - Part 100: Additional specifications to DIN EN 752 and DIN EN 12056
• DIN 1986-4 Drainage systems on private ground - Part 4: Fields of application of sewage pipes and fittings of different materials*， 2019-08-01 Update
• DIN 4034-2 Prefabricated concrete manholes, unreinforced, steel fibre and reinforced - Part 2: Manholes for well construction and drain construction*， 2013-05-01 Update
• DIN 4045 Wastewater engineering - Vocabulary*， 2016-11-01 Update
• DIN 4060 Joints of sewer and drain pipes with elastomeric seals - Requirements and testing on joints with elastomeric seals*， 2016-07-01 Update
• DIN 4281:1998 Concrete for prefabricated sewage units - Manufacture, requirements, testing and quality control
• DIN EN 476 General requirements for components used in drains and sewers; German version EN 476:2022*， 2022-09-01 Update
• DIN EN 681-1 Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber; German and English version prEN 681-1:2016*， 2016-07-01 Update
• DIN EN 681-3 Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 3: Cellular materials of vulcanized rubber; German version EN 681-3:2000 + A1:2002 + A2:2005*， 2006-11-01 Update
• DIN EN 752-1 Drainage systems outside buildings DIN Part 1: General and definitions
• DIN EN 752-2 Drainage systems outside buildings
• DIN EN 752-3:1996 Drainage systems outside buildings DIN Part 3: Planning
• DIN EN 752-4 Drainage systems outside buildings Part 4: Hydraulic calculation and environmental aspects
• DIN EN 752-5 Drainage systems outside buildings Part 5: Renovation
• DIN EN 752-6 
• DIN EN 752-7 Drain and sewer systems outside buildings — Part 7: Maintenance and operations
• DIN V 4034-1 Prefabricated concrete manholes, unreinforced, steel fibre and reinforced for drains and sewers - Type 1 and Type 2 - Part 1: Requirements, test methods and evaluation of conformity

DIN 4040-100:2004 history

• 2016 DIN 4040-100:2016-12 Grease separators - Part 100: Application provisions for grease separators in accordance with DIN EN 1825-1 and DIN EN 1825-2 / Note: Applies in conjunction with DIN EN 1825-1 (2004-12), DIN EN 1825-2 (2002-05).
• 2016 DIN 4040-100:2016 Grease separators - Part 100: Application provisions for grease separators in accordance with DIN EN 1825-1 and DIN EN 1825-2
• 2004 DIN 4040-100:2004 Grease separators - Part 100: Requirements relating to the use of separators to DIN EN 1825-1 and DIN EN 1825-2
• 1970 DIN 4040-100 E:2002-07 Grease separators - Part 100: Application provisions for grease separators in accordance with DIN EN 1825-1 and DIN EN 1825-2
• 2002 DIN EN 1825-2:2002 Grease separators - Part 2: Selection of nominal size, installation, operation and maintenance; German version EN 1825-2:2002
• 1970 DIN V 4040-2:1999
• 1970 DIN 4040-1:1989