ASTM A671/A671M-10
Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures

Standard No.

ASTM A671/A671M-10

Release Date

2010

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM A671/A671M-13

Latest

ASTM A671/A671M-20

Scope

1.1 This specification covers a variety of carbon, alloy, and martensitic stainless steel nuts in the size range ¼ through 4 in. and metric M6 through M100 nominal. It also covers austenitic stainless steel nuts in the size range ¹/₄ in. and M6 nominal and above. These nuts are intended for high-pressure or high-temperature service, or both. Grade substitutions without the purchaser''s permission are not allowed.

1.2 Bars from which the nuts are made shall be hot-wrought. The material may be further processed by centerless grinding or by cold drawing. Austenitic stainless steel may be solution annealed or annealed and strain-hardened. When annealed and strain hardened austenitic stainless steel is ordered in accordance with Supplementary Requirement S1, the purchaser should take special care to ensure that 8.2.2, Supplementary Requirement S1, and Appendix X1 are thoroughly understood.

1.3 Supplementary requirements (S1 through S8) of an optional nature are provided. These shall apply only when specified in the inquiry, contract, and order.

1.4 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable“ M” specification designation (SI units), the material shall be furnished to inch-pound units.

1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Within the text, the SI units are shown in brackets.

ASTM A671/A671M-10 Referenced Document

• ASTM A20/A20M Standard Specification for General Requirements for Steel Plates for Pressure Vessels
• ASTM A203/A203M Standard Specification for Pressure Vessel Plates, Alloy Steel, Nickel
• ASTM A285/A285M Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength
• ASTM A299/A299M Standard Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Silicon
• ASTM A353/A353M Standard Specification for Pressure Vessel Plates, Alloy Steel, 9 Percent Nickel, Double-Normalized and Tempered
• ASTM A370 Standard Test Methods and Definitions for Mechanical Testing of Steel Products
• ASTM A435/A435M Standard Specification for Straight-Beam Ultrasonic Examination of Steel Plates
• ASTM A515/A515M Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service
• ASTM A516/A516M Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service
• ASTM A517/A517M Standard Specification for Pressure Vessel Plates, Alloy Steel, High-Strength, Quenched and Tempered
• ASTM A530/A530M Standard Specification for General Requirements for Specialized Carbon and Alloy Steel Pipe
• ASTM A537/A537M Standard Specification for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel
• ASTM A553/A553M Standard Specification for Pressure Vessel Plates, Alloy Steel, Quenched and Tempered 8 and 9 Percent Nickel
• ASTM A577/A577M Standard Specification for Ultrasonic Angle-Beam Examination of Steel Plates
• ASTM A578/A578M Standard Specification for Straight-Beam Ultrasonic Examination of Plain and Clad Steel Plates for Special Applications
• ASTM A736/A736M Standard Specification for Pressure Vessel Plates, Low-Carbon Age-Hardening Nickel-Copper-Chromium-Molybdenum-Columbium and Nickel-Copper-Manganese-Molybdenum-Columbium Alloy Steel
• ASTM E110 Standard Test Method for Indentation Hardness of Metallic Materials by Portable Hardness Testers
• ASTM E165 Standard Test Method for Liquid Penetrant Examination
• ASTM E709 Standard Guide for Magnetic Particle Examination

ASTM A671/A671M-10 history

• 2020 ASTM A671/A671M-20 Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures
• 2019 ASTM A671/A671M-19 Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures
• 2016 ASTM A671/A671M-16a Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures
• 2016 ASTM A671/A671M-16 Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures
• 2014 ASTM A671/A671M-14 Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures
• 2013 ASTM A671/A671M-13e1 Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures
• 2013 ASTM A671/A671M-13 Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures
• 2010 ASTM A671/A671M-10 Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures
• 2009 ASTM A671-09 Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures
• 2006 ASTM A671-06 Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures
• 2004 ASTM A671-04 Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures
• 1996 ASTM A671-96(2001) Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures
• 1996 ASTM A671-96 Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures
• 1994 ASTM A671-94 Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures