ASTM D4555-10
Standard Test Method for Determining Deformability and Strength of Weak Rock by an In Situ Uniaxial Compressive Test

Standard No.

ASTM D4555-10

Release Date

2010

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM D4555-10

Scope

Since there is no reliable method of predicting the overall strength and deformation data of a rock mass from the results of laboratory tests on small specimens, in situ tests on large specimens are necessary, especially if the specimen size required for a given grain size would exceed the size that can be obtained for or tested in a laboratory as stated in Test Method D7012. Such tests also have the advantage that the rock specimen is tested under similar environmental conditions as prevailing for the rock mass.

Since the strength of rock is dependent on the size of the test specimen and discontinuities, it is necessary to test several specimens (laboratory or field, or both) of progressively increasing size until an asymptotically constant strength value is found. This value is taken to represent the strength of the rock mass. ^,

Note 18212;Notwithstanding the statements on precision and bias contained in this test method; the precision of this test method is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice are generally considered capable of competent and objective testing. Users of this test method are cautioned that compliance with Practice does not in itself assure reliable testing. Reliable testing depends on many factors. Practice provides a means of evaluating some of those factors.

The test method is shown only being conducted underground and vertical. However, this test method could be done in a quarry or on the surface if a reaction frame could be set up to behave as a reactive surface in place of a tunnel crown.

1.1 This test method covers the measurement of the deformability and strength of large in situ specimens of rock by a uniaxial compressive test. The test results take into account the effect of both intact material behavior and the behavior of discontinuities contained within the specimen block.

1.2 This test method does not cover which type of specimen should be tested or whether anisotropic factors should be considered. The specifics of the test program need to be developed prior to testing and possibly even before sampling. Such specifics would be dependent on the intended use of the data, as well as any budgetary constraints and other factors, which are outside the scope of this test method.

1.3 Theoretically there is no limit to the size of the test specimen; however, size will be controlled by the strength of the test specimen relative to the capacity of any loading apparatus and bearing capacity of the surface the apparatus must react against. Furthermore, the orientation and strength of discontinuities relative to the specimen geometry will be a factor limiting specimen size too.

1.4 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.

1.5 The values stated in SI units are to be regarded as the standard.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM D4555-10 Referenced Document

• ASTM D2216 Standard Test Method for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
• ASTM D3740 Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
• ASTM D6026 Standard Practice for Using Significant Digits in Geotechnical Data
• ASTM D6032 Standard Test Method for Determining Rock Quality Designation (RQD) of Rock Core
• ASTM D653 Standard Terminology Relating to Soil, Rock, and Contained Fluids
• ASTM D7012 Standard Test Methods for Compressive Strength and Elastic Moduli of Intact Rock Core Specimens under Varying States of Stress and Temperatures

ASTM D4555-10 history

• 2010 ASTM D4555-10 Standard Test Method for Determining Deformability and Strength of Weak Rock by an In Situ Uniaxial Compressive Test
• 2001 ASTM D4555-01(2005) Standard Test Method for Determining Deformability and Strength of Weak Rock by an In Situ Uniaxial Compressive Test
• 2001 ASTM D4555-01 Standard Test Method for Determining Deformability and Strength of Weak Rock by an In Situ Uniaxial Compressive Test
• 1990 ASTM D4555-90(1995) Standard Test Method for Determining Deformability and Strength of Weak Rock by an In Situ Uniaxial Compressive Test