DIN EN ISO 10350-1:2010
Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2007); German version EN ISO 10350-1:2008
- Standard No.
- DIN EN ISO 10350-1:2010
- Release Date
- 2010
- Published By
- German Institute for Standardization
- Status
- Replace By
- DIN EN ISO 10350-1:2014
- DIN EN ISO 10350-1 A1 E:2011-05
- Latest
- DIN EN ISO 10350-1:2018-03
- Replace
- DIN EN ISO 10350-1:2008
- Scope
- This standard identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. This part of the standard applies predominantly to unreinforced and reinforced thermoplastic and thermosetting materials that may be injection- or compression-moulded or prepared as sheets of specified thickness.
DIN EN ISO 10350-1:2010 Referenced Document
- IEC 60093 Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials
- IEC 60243 Recommended methods of test for electric strength of solid insulating materials at power frequencies
- ISO 1133 Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics; Technical Corrigendum 1
- ISO 11357-3 Plastics - Differential scanning calorimetry (DSC) - Part 3: Determination of temperature and enthalpy of melting and crystallization*， 2018-03-01 Update
- ISO 11359-2 Plastics — Thermomechanical analysis (TMA) — Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature*， 2021-11-12 Update
- ISO 1183-1 Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pycnometer method and titration method*， 2019-02-28 Update
- ISO 1183-2 Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient column method*， 2019-02-28 Update
- ISO 1183-3 Plastics - Methods for determining the density of non-cellular plastics - Part 3: Gas pyknometer method
- ISO 179-1 Plastics. Determination of Charpy impact properties - Non-instrumented impact test*， 2023-06-07 Update
- ISO 179-2 Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test — Amendment 1: Precision data*， 2020-05-14 Update
- ISO 2577 Plastics - Thermosetting moulding materials - Determination of shrinkage
- ISO 2818 Plastics — Preparation of test specimens by machining*， 2018-12-13 Update
- ISO 291 Plastics - Standard atmospheres for conditioning and testing
- ISO 293 Plastics — Compression moulding of test specimens of thermoplastic materials*， 2023-02-21 Update
- ISO 294-1 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens*， 2017-05-01 Update
- ISO 294-3 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates*， 2020-06-26 Update
- ISO 294-4 Milling cutters mounted on centring arbors having a 7/24 taper; Fitting dimensions; Centring arbors*， 2018-12-20 Update
- ISO 295 Plastics - Compression moulding of test specimens of thermosetting materials
- ISO 306 Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)*， 2022-11-18 Update
- ISO 3167 Plastics - Multipurpose test specimens*， 2014-08-01 Update
- ISO 4589-2 Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test*， 2017-04-01 Update
- ISO 527-1 Plastics — Determination of tensile properties — Part 1: General principles*， 2019-07-26 Update
- ISO 527-2 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics*， 2012-02-01 Update
- ISO 6603-2 Plastics. Determination of puncture impact behaviour of rigid plastics. - Part 2: Instrumented impact testing*， 2023-06-02 Update
- ISO 8256 Plastics*， 2023-11-01 Update
- ISO 899-1 Plastics - Determination of creep behaviour - Part 1: Tensile creep*， 2017-09-01 Update
DIN EN ISO 10350-1:2010 history
- 2018 DIN EN ISO 10350-1:2018-03 Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2017); German version EN ISO 10350-1:2017
- 2018 DIN EN ISO 10350-1:2018 Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2017)
- 1970 DIN EN ISO 10350-1 E:2016-08 Acquisition and presentation of comparable single point data for plastics Part 1: Molding materials (draft)
- 2016 DIN EN ISO 10350-1 E:2016 Draft Document - Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO/DIS 10350-1:2016); German and English version prEN ISO 10350-1:2016
- 2014 DIN EN ISO 10350-1:2014 Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2007 + Amd 1:2014); German version EN ISO 10350-1:2008 + A1:2014
- 2010 DIN EN ISO 10350-1:2010 Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2007); German version EN ISO 10350-1:2008
- 2008 DIN EN ISO 10350-1:2008 Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2007); German version EN ISO 10350-1:2008
- 1970 DIN EN ISO 10350-1:2001 Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials
