ASTM C1710-09
Standard Guide for Installation of Flexible Closed Cell Preformed Insulation in Tube and Sheet Form

Standard No.
ASTM C1710-09
Release Date
2009
Published By
American Society for Testing and Materials (ASTM)
Status
Replace By
ASTM C1710-11
Latest
ASTM C1710-22
Scope

This guide applies to flexible closed cell insulation tubing and sheet materials manufactured according to Specification C534 and Specification C1427. This standard is intended to provide a basic guide for installing these types of materials.

Confirm application use temperature is consistent with specified use temperature for material as defined in ASTM Specifications unless otherwise agreed upon with the manufacturer. There are different grades for each of the insulation types referred to in this guide, material and grade installed should be that specified.

This guide is not intended to cover all aspects associated with installation for all applications, consult the National, Commercial Industrial Insulation Standards (MICA Manual) or the specific product manufacturer for recommendations, or both. (See ASHRAE Handbook (Fundamentals Chapter 26) and ASHRAE Handbook (Refrigeration Chapter 33)

1.1 This guide covers recommended installation techniques for flexible closed cell pre-formed insulation in tube or sheet form. This guide is applicable to materials manufactured in accordance with Specification C534 (Elastomeric based insulation) or Specification C1427 (polyolefin based insulation). The materials covered in this guide encompass a service temperature of -297°F to 300°F ( -183°C to 150 °C) as indicated in the material specifications referenced above. Many of the recommendations made are specific to below ambient applications only.

1.2 The purpose of this guide is to optimize the thermal performance and longevity of installed closed cell flexible insulation systems. By following this guide, the owner, and designer can expect to achieve the energy savings expected and prevention of condensation under the specified design conditions. This document is limited to installation procedures and does not encompass system design.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM C1710-09 Referenced Document

  • ASTM C1427 Specification for Preformed Flexible Cellular Polyolefin Thermal Insulation in Sheet and Tubular Form
  • ASTM C168 Standard Terminology Relating to Thermal Insulation
  • ASTM C534 Standard Specification for Preformed Flexible Elastomeric Cellular Thermal Insulation in Sheet and Tubular Form
  • ASTM C585 Standard Practice for Inner and Outer Diameters of Rigid Thermal Insulation for Nominal Sizes of Pipe and Tubing (NPS System)

ASTM C1710-09 history

  • 2022 ASTM C1710-22 Standard Guide for Installation of Flexible Closed Cell Preformed Insulation in Tube and Sheet Form
  • 2021 ASTM C1710-21a Standard Guide for Installation of Flexible Closed Cell Preformed Insulation in Tube and Sheet Form
  • 2021 ASTM C1710-21 Standard Guide for Installation of Flexible Closed Cell Preformed Insulation in Tube and Sheet Form
  • 2020 ASTM C1710-20 Standard Guide for Installation of Flexible Closed Cell Preformed Insulation in Tube and Sheet Form
  • 2016 ASTM C1710-16 Standard Guide for Installation of Flexible Closed Cell Preformed Insulation in Tube and Sheet Form
  • 2015 ASTM C1710-15 Standard Guide for Installation of Flexible Closed Cell Preformed Insulation in Tube and Sheet Form
  • 2011 ASTM C1710-11 Standard Guide for Installation of Flexible Closed Cell Preformed Insulation in Tube and Sheet Form
  • 2009 ASTM C1710-09 Standard Guide for Installation of Flexible Closed Cell Preformed Insulation in Tube and Sheet Form
Standard Guide for Installation of Flexible Closed Cell Preformed Insulation in Tube and Sheet Form



Copyright ©2024 All Rights Reserved