ISO 10684:2004
Fasteners - Hot dip galvanized coatings
- Standard No.
- ISO 10684:2004
- Release Date
- 2004
- Published By
- International Organization for Standardization (ISO)
- Status
- Replace By
- ISO 10684:2004/cor 1:2008
- Latest
- ISO 10684:2004/cor 1:2008
- Scope
- This International Standard specifies material, process, dimensional and some performance requirements for hot dip spun galvanized coatings applied to coarse threaded steel fasteners from M8 up to and including M64 and for property classes up to and including 10.9 for bolts, screws and studs and 12 for nuts. It is not recommended to hot dip galvanize threaded fasteners in diameters smaller than M8 and/or with pitches below 1,25 mm. NOTE Attention is drawn to the fact that the proof loads and stresses under proof load of oversize tapped nuts with threads M8 and M10 and the ultimate tensile loads and proof loads of undersize threaded bolts and screws with threads M8 and M10 are reduced as compared to the values specified in ISO 898-2 and ISO 898-1 respectively and are specified in Annex A. It primarily concerns the spun hot dip galvanizing of threaded steel fasteners, but it may also be applied to other threaded steel parts. The specifications given in this International Standard may also be applied to non-threaded steel parts such as washers.
ISO 10684:2004 Referenced Document
- ISO 1460 Metallic coatings — Hot dip galvanized coatings on ferrous materials — Determination of the mass per unit area — Gravimetric method*， 2020-09-14 Update
- ISO 1461 Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods*， 2022-08-02 Update
- ISO 2064 Metallic and other inorganic coatings - Definitions and conventions concerning the measurement of thickness
- ISO 2178 Non-magnetic coatings on magnetic substrates - Measurement of coating thickness - Magnetic method*， 2016-03-01 Update
- ISO 898-1 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread; Technical Corrigendum 1*， 2013-04-01 Update
- ISO 898-2 Fasteners — Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes*， 2022-09-30 Update
- ISO 8991 Designation system for fasteners
- ISO 965-1 ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data — Amendment 1*， 2021-09-29 Update
- ISO 965-2 ISO general purpose metric screw threads - Tolerances - Part 2: Limits of sizes for general purpose external and internal screw threads - Medium quality; Amendment 1*， 2021-06-30 Update
- ISO 965-3 ISO general purpose metric screw threads - Tolerances - Part 3: Limit deviations for screw threads*， 2021-06-30 Update
- ISO 965-4 ISO general purpose metric screw threads - Tolerances - Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing*， 2021-06-30 Update
- ISO 965-5 ISO general purpose metric screw threads — Tolerances — Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance positio*， 2021-07-06 Update
ISO 10684:2004 history
- 2008 ISO 10684:2004/cor 1:2008 Fasteners - Hot dip galvanized coatings; Technical Corrigendum 1
- 2004 ISO 10684:2004 Fasteners - Hot dip galvanized coatings
