DIN EN 598:2009
Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods(includes Amendment A1:2009); English version of DIN EN 598:2009-10

Standard No.

DIN EN 598:2009

Release Date

2009

Published By

German Institute for Standardization

Status

Be replaced

Replace By

DIN EN 598 A1 E:2009-02

Latest

DIN EN 598 E:2017-11

Replace

DIN EN 598:2008 DIN EN 598/A1:2009

Scope

This European Standard specifies the requirements and associated test methods applicable to ductile iron pipes fittings, accessories and their joints for the construction of drains and sewers outside buildings: -- operating without pressure (gravity sewerage), or with positive or negative pressure (see Table 5); to be installed below or above ground; -- to convey surface water, domestic waste water and certain types of industrial effluents, either in separate systems or in combined systems. This European Standard applies to pipes, fittings and accessories which are: -- manufactured with socketed, flanged or spigot ends; -- normally delivered externally and internally coated; -- suitable for continuous fluid temperatures between 0 ℃ excluding frost, and 45 ℃ for DN ≤ 200 or 35 ℃ forv DN > 200, according to EN 476: -- not intended for use in areas subject to reaction to fire regulations NOTE 1 This does not preclude special arrangements for the products to be used at higher temperatures. This European Standard covers pipes, fittings and accessories cast by any type of foundry process or manufactured by fabrication of cast components, as well as corresponding joints, of a size range extending from DN 80 to DN 2000 inclusive. This European Standard specifies requirements for materials, dimensions and tolerances, mechanical properties and standard coatings of ductile iron pipes and fittings. It also gives performance requirements for all components including joints. Joint design and gasket shapes are outside the scope of this European Standard. NOTE 2 In this European Standard. all pressures are relative pressures, expressed in bars (100 kPa = 1 bar).

DIN EN 598:2009 Referenced Document

• EN 10002-1 Metallic Materials - Tensile Testing - Part 1: Method of Test at Ambient Temperature
• EN 1092-2 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges*， 2023-11-29 Update
• EN 14901 Ductile iron pipes@ fittings and accessories - Requirements and test methods for organic coatings of ductile iron fittings and accessories - Part 1: Epoxy coating (heavy duty)*， 2018-11-01 Update
• EN 196-1 Methods of testing cement - Part 1: Determination of strength*， 2016-04-01 Update
• EN 545 Ductile iron pipes, fittings, accessories and their joints for water pipelines - Requirements and test methods*， 2010-09-01 Update
• EN 681-1 Elastomeric seals Material requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber (Incorporates Amendments A1: 1998 and A2: 2002; Incorporating Corrigendum August 2002; Incorporates Amendment A3: 2005)
• EN ISO 4016 Fasteners - Hexagon head bolts - Product grade C (ISO 4016:2022)*， 2022-07-20 Update
• EN ISO 4034 Hexagon regular nuts (style 1) - Product grade C - Technical Corrigendum 1 (ISO 4034:2012/Cor 1:2013)*， 2013-05-01 Update
• EN ISO 6506-1 Metallic materials - Brinell hardness test - Part 1: Test method*， 2014-09-01 Update
• EN ISO 7091 Plain Washers - Normal Series - Product Grade C ISO 7091:2000
• EN ISO 9001:2000 Quality Management Systems - Requirements Supersedes EN ISO 9002:1994 and EN ISO 9003:1994; ISO 9001:2000*， 2024-04-19 Update

DIN EN 598:2009 history

• 1970 DIN EN 598 E:2017-11 Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods
• 2009 DIN EN 598:2009-10 Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods; German version EN 598:2007+A1:2009 / Note: To be replaced by DIN EN 598 (2017-11).
• 1970 DIN EN 598 A1 E:2009-02
• 2009 DIN EN 598:2009 Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods(includes Amendment A1:2009); English version of DIN EN 598:2009-10
• 2008 DIN EN 598:2008 Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods; German version EN 598:2007
• 1970 DIN EN 598:1994 Ductile iron pipes, fittings, accessories and their joints for sewerage applications - Requirements and test methods