BS EN 14382:2005+A1:2009 Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar
This document specifies constructional, functional, testing and marking requirements, sizing and
documentation of gas safety shut-off devices used in the pressure regulating stations in accordance with
EN 12186 or EN 12279:
- for inlet pressures up to 100 bar and nominal diameters up to DN 400;
- for an operating temperature range from –20 °C to +60 °C, which operate with fuel gases of the 1st and 2nd family in accordance with EN 437 in transmission and distribution networks and also in commercial and industrial installations.
"Gas safety shut-off devices" will hereafter be called "SSDs" except in titles.
For standard safety shut-off devices when used in pressure regulating stations complying with EN 12186
or EN 12279, Annex ZA lists all applicable Essential Requirements except the external corrosion resistance in case of environmental conditions where corrosion is likely to occur."
This document considers the following classes/types of SSDs:
temperature classes:
- class 1: operating temperature range from –10 °C to 60 °C;
- class 2: operating temperature range from –20 °C to 60 °C;
functional classes:
-class A: SSDs that close when damage to the pressure detector element occurs (applicable to
overpressure SSDs only) or when external power fails and whose re-opening, after an intervention for
overpressure, is possible only manually;
- class B: SSDs that do not close when damage to the pressure detector element occurs and whose reopening, after an intervention for overpressure, is possible only manually;
SSDs types:
- type IS: (integral strength type);
- type DS: (differential strength type).
SSDs complying with the requirements of this document may be declared as “in conformity with
EN 14382“ and bear the mark “EN 14382”.
The material and functional requirements specified in this document may be applied to SSDs which use
thermal energy or the effects of electrical energy to trip the operation of the closing member. For these SSDs the operational parameters are not specified in this document.
This document does not apply to:
- SSDs upstream from/on/in domestic gas-consuming appliances which are installed downstream of
domestic gas meters;
- SSDs incorporated into pressure-regulating devices used in service lines with volumetric flow rate
≤ 200 m3/h at normal conditions and inlet pressure ≤ 5 bar.
BS EN 14382:2005+A1:2009 Referenced Document
EN 10226-1 Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads; Dimensions, tolerances and designation
EN 10226-2 Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation
EN 1092-1:2007 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 1: Steel flanges (Incorporates Amendment A1: 2013; Incorporating Corrigendum May 2014)*， 2007-08-01 Update
EN 12186 Gas infrastructure - Gas pressure regulating stations for transmission and distribution - Functional requirements*， 2014-10-01 Update
EN 12279 Gas supply systems - Gas pressure regulating installations on service lines - Functional requirements
EN 12516-1:2005 Industrial valves - Shell design strength - Part 1: Tabulation method for steel valve shells
EN 12516-2:2004 Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells
EN 12516-4:2008 Industrial valves - Shell design strength - Part 4: Calculation method for valve shells manufactured in metallic materials other than steel*， 2008-01-01 Update
EN 12627 Industrial valves - Butt welding ends for steel valves*， 2017-11-01 Update
EN 13445-4 Unfired pressure vessels - Part 4: Fabrication*， 2017-01-01 Update
EN 13906-1 Cylindrical helical springs made from round wire and bar - Calculation and design - Part 1 : Compression springs*， 2013-07-01 Update
EN 13906-2 Cylindrical helical springs made from round wire and bar - Calculation and design - Part 2: Extension springs*， 2013-06-01 Update
EN 1759-1 Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, class designated - Part 1: Steel flanges, NPS 1/2 to 24*， 2024-04-19 Update
EN 287-1:1992 Approval testing of welders; fusion welding; part 1: steels
EN 334:2005 Gas pressure regulators for inlet pressures up to 100 bar (Incorporates Amendment A1: 2009)
EN 473:2000 Non-Destructive Testing - Qualification and Certification of NDT Personnel - General Principles includes amendment A1:2005; Supersedes CR 12459:1996*， 2024-04-19 Update
EN 60534-1:1993 Industrial-Process Control Valves Part 1: Control Valve Terminology and General Considerations
EN 970:1997 Non-Destructive Examination of Fusion Welds - Visual Examination
EN ISO 175:2000 Plastics - Methods of Test for the Determination of the Effects of Immersion in Liquid Chemicals
EN ISO 9606-2:2004 Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004)*， 2024-04-19 Update
BS EN 14382:2005+A1:2009 history
2019BS EN 14382:2019 Gas safety shut-off devices for inlet pressure up to 10 MPa (100 bar)
2006BS EN 14382:2005+A1:2009 Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar
2006BS EN 14382:2005 Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar
2003BS EN 14382:2002 Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for operating pressure up to 100 bar