DIN EN 1852-1:2009
Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system; English version of DIN EN 1852-1:2009-07

Standard No.

DIN EN 1852-1:2009

Release Date

2009

Published By

German Institute for Standardization

Status

Be replaced

Replace By

DIN EN 1852-1 E:2016

Latest

DIN EN 1852-1:2023-07

Replace

DIN EN 1852-1:2003 DIN EN 1852-1:2007

Scope

This part of EN 1852 specifies the requirements for solid wall pipes, fittings and the system of polypropylene (PP) piping systems intended for use for: non-pressure underground drainage and sewerage outside the building structure (application area code "U"), and -- non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code "D") and outside the building structure. This is reflected in the marking of products by "U" and "UD" This standard covers PP materials without mineral modifiers t also specifies the test parameters for the test methods referred to in this standard This standard covers a range of nominal sizes, and pipe series and gives recommendations concerning colours. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects taking into account their particular requirements and any relevant national regulations and installation practices or codes. In conjunction with Part 2 and Part 3 of EN 1852 it is applicable to PP pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage. This standard is applicable to PP pipes and fittings with or without an integral socket NOTE 2 The fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings NOTE 3 Requirements and limiting values for application area code "D" are given in Table 4, Table 7 and Table 14 NOTE 4 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex C can be connected to pipes and fittings conforming to this standard, when they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 14.

DIN EN 1852-1:2009 Referenced Document

• EN 1053 Plastics piping systems - Thermoplastics piping systems for non-pressure applications - Test method for watertightness
• EN 1055:1996 Plastics piping systems - Thermoplastics piping systems for soil and waste discharge inside buildings - Test method for resistance to elevated temperature cycling
• EN 12061 Plastics piping systems - Thermoplastics fittings - Test method for impact resistance
• EN 12256 Plastics piping systems - Thermoplastics fittings - Test method for mechanical strength or flexibility of fabricated fittings
• EN 1277:2003 Plastics piping systems - Thermoplastics piping systems for buried non-pressure applications - Test methods for leaktightness of elastomeric sealing ring type joints*， 2024-04-19 Update
• EN 1411:1996 Plastics piping and ducting systems - Thermoplastics pipes - Determination of resistance to external blows by the staircase method
• EN 681-1 Elastomeric seals Material requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber (Incorporates Amendments A1: 1998 and A2: 2002; Incorporating Corrigendum August 2002; Incorporates Amendment A3: 2005)
• EN 681-2 Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers
• EN 728 Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time
• EN 744:1995 Plastics piping and ducting systems - Thermoplastics pipes - Test method for resistance to external blows by the round-the-clock method
• EN ISO 1043-1:2001 Plastics - Symbols and Abbreviated Terms - Part 1: Basic Polymers and Their Special Characteristics
• EN ISO 1133 Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
• EN ISO 1167-1 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006)
• EN ISO 2505:2005 Thermoplastics pipes - Longitudinal reversion - Test method and parameters
• EN ISO 3126 Plastics piping systems - Plastics components - Determination of dimensions ISO 3126:2005
• EN ISO 472:2001 Plastics - Vocabulary
• EN ISO 580:2005 Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO 580:2005)
• EN ISO 9969 Thermoplastics pipes - Determination of ring stiffness*， 2016-01-01 Update

DIN EN 1852-1:2009 history

• 2023 DIN EN 1852-1:2023-07 Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system; German version EN 1852-1:2018+A1:2022
• 2023 DIN EN 1852-1:2023 Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system (includes Amendment A1:2022)
• 2022 DIN EN 1852-1/A1:2022 Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system; German and English version EN 1852-1:2018/prA1:2021
• 2018 DIN EN 1852-1:2018-03 Diving suits - Part 2: Dry suits - Requirements and test methods; German version EN 14225-2:2017
• 2018 DIN EN 1852-1:2018 Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
• 1970 DIN EN 1852-1 E:2016-05 Plastics piping systems for non-pressure underground drainage and sewerage — Polypropylene (PP) — Part 1: Specifications for pipes, fittings and the system
• 2016 DIN EN 1852-1 E:2016 Draft Document - Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system; German and English version prEN 1852-1:2016
• 2009 DIN EN 1852-1:2009 Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system; English version of DIN EN 1852-1:2009-07
• 1997 DIN EN 1852-1:2003 Plastics piping systems for non-pressure underground drainage and sewerage — Polypropylene (PP) — Part 1: Specifications for pipes, fittings and the system (includes amendment A1:2002)