ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for
certain basic properties of plastics. In general, each property is specified by a single experimental value,
although in certain cases properties are represented by two values obtained under different test conditions.
The properties included are those presented conventionally in manufacturers' data sheets. This part of
ISO 10350 applies predominantly to unreinforced and reinforced thermoplastic and thermosetting materials
that may be injection- or compression-moulded or prepared as sheets of specified thickness. Part 2 of
ISO 10350 deals specifically with long- or continuous-fibre-reinforced plastics. For the purposes of ISO 10350,
long-fibre-reinforced plastics are considered to have fibre lengths greater than 7,5 mm prior to moulding.
BS EN ISO 10350-1:2008 Referenced Document
ISO 1133 Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics; Technical Corrigendum 1
ISO 1183-1 Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pycnometer method and titration method*, 2019-02-28 Update
ISO 1183-2 Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient column method*, 2019-02-28 Update
ISO 1183-3 Plastics - Methods for determining the density of non-cellular plastics - Part 3: Gas pyknometer method
ISO 178 Surface chemical analysis — Secondary ion mass spectrometry — Linearity of intensity scale in single ion counting time-of-flight mass analysers*, 2019-04-01 Update
ISO 179-1 Plastics. Determination of Charpy impact properties - Non-instrumented impact test*, 2023-06-07 Update
ISO 179-2 Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test — Amendment 1: Precision data*, 2020-05-14 Update
ISO 2577 Plastics - Thermosetting moulding materials - Determination of shrinkage
ISO 2818 Plastics — Preparation of test specimens by machining*, 2018-12-13 Update
ISO 291 Plastics - Standard atmospheres for conditioning and testing
ISO 293 Plastics — Compression moulding of test specimens of thermoplastic materials*, 2023-02-21 Update
ISO 294-1 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens*, 2017-05-01 Update
ISO 294-3 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates*, 2020-06-26 Update
ISO 294-4 Milling cutters mounted on centring arbors having a 7/24 taper; Fitting dimensions; Centring arbors*, 2018-12-20 Update
ISO 295 Plastics - Compression moulding of test specimens of thermosetting materials
ISO 306 Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)*, 2022-11-18 Update
ISO 3167 Plastics - Multipurpose test specimens*, 2014-08-01 Update
ISO 4589-2 Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test*, 2017-04-01 Update
ISO 527-1 Plastics — Determination of tensile properties — Part 1: General principles*, 2019-07-26 Update
ISO 527-2 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics*, 2012-02-01 Update
ISO 62 Plastics - Determination of water absorption
ISO 6603-2 Plastics. Determination of puncture impact behaviour of rigid plastics. - Part 2: Instrumented impact testing*, 2023-06-02 Update
ISO 75-1 Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics*, 2020-02-28 Update
ISO 75-2 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite*, 2013-04-01 Update
ISO 899-1 Plastics - Determination of creep behaviour - Part 1: Tensile creep*, 2017-09-01 Update
BS EN ISO 10350-1:2008 history
2018BS EN ISO 10350-1:2017 Plastics. Acquisition and presentation of comparable single-point data. Moulding materials
2014BS EN ISO 10350-1:2008+A1:2014 Plastics. Acquisition and presentation of comparable single-point data-Moulding materials
2008BS EN ISO 10350-1:2008 Plastics - Acquisition and presentation of comparable singlepoint data - Part 1: Moulding materials