ASTM A325M-09
Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength [Metric]

Standard No.

ASTM A325M-09

Release Date

2009

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM A325-09a

Latest

ASTM A325M-14

Scope

1.1 This specification covers two types of quenched and tempered, steel, metric heavy hex structural bolts having a minimum tensile strength of 830 MPa (Note 1).

1.2 The bolts are intended for use in structural connections. These connections are comparable to those covered under the requirements of the Specification for Structural Joints using ASTM A 325 or A 490 bolts, approved by the Research Council on Structural Connections; endorsed by the American Institute of Steel Construction and by the Industrial Fastener Institute.

1.3 The bolts are furnished in sizes M12 to M36 inclusive. They are designated by type denoting chemical composition as follows:

1.3.1 Type 18212;Medium-carbon, carbon boron, medium carbon alloy, or alloy boron steel.

1.3.2 Type 28212;Withdrawn in 2003.

1.3.3 Type 38212;Weathering Steel.

1.4 This specification is applicable to metric heavy hex, structural bolts only.

1.5 Terms used in this specification are defined in Terminology F 1789.

1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

Note 18212;This specification is the metric companion to the inch pound Specification A 325.

1.7 The following safety hazard caveat pertains only to the test methods portion, Section 10, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM A325M-09 history

• 2014 ASTM A325M-14 Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength &40;Metric&41;
• 2013 ASTM A325M-13 Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength (Metric)
• 2010 ASTM A325-10e1 Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength
• 2010 ASTM A325-10 Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength
• 2009 ASTM A325-09ae1 Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength
• 2009 ASTM A325-09a Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength
• 2009 ASTM A325M-09 Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength [Metric]
• 2008 ASTM A325M-08 Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength [Metric]
• 2007 ASTM A325-07a Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength
• 2007 ASTM A325M-07 Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength [Metric]
• 2006 ASTM A325-06 Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength
• 2005 ASTM A325M-05 Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength [Metric]
• 2004 ASTM A325M-04b Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength [Metric]
• 2004 ASTM A325M-04a Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength [Metric]
• 2004 ASTM A325M-04 Standard Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength [Metric]
• 2003 ASTM A325M-03 Standard Specification for Structural Bolts, Steel, Heat Treated 830 Mpa Minimum Tensile Strength [Metric]
• 2002 ASTM A325-02 Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength
• 2000 ASTM A325M-00 Standard Specification for High-Strength Bolts for Structural Steel Joints [Metric]
• 1979 ASTM A325-79 Standard Specification for High-Strength Bolts For Structural Steel Joints