DIN EN 528:2009
Rail dependent storage and retrieval equipment - Safety requirements; English version of DIN EN 528:2009-02

Standard No.

DIN EN 528:2009

Release Date

2009

Published By

German Institute for Standardization

Status

Be replaced

Replace By

DIN EN 528 E:2019

Latest

DIN EN 528 E:2019

DIN EN 528:2019

DIN EN 528:2023

Replace

DIN EN 528/A1:2003 DIN EN 528:2005 DIN EN 528:1996

Scope

This standard applies to all types of SIR machines, restricted to the rails on which they travel within and outside the aisles, which embody lifting means and may embody lateral handling facilities, for the storage and retrieval of unit loads and/or long goods such as bar materials and/or for order picking or similar duties. Also included is the transfer equipment used to change between aisles. Control of machines may range from manual to fully automatic. This standard does not apply to free ranging industrial trucks or robots. References in this standard to racking, buildings and systems only apply where it is necessary to assess the hazards and risks at their interfaces with SIR machines. This standard deals with all significant hazards relevant to rail dependent storage and retrieval equipment, when they are used as intended under the conditions foreseen by the manufacturer (see Clause 4). This standard applies to machines and equipment that are manufactured after the date of issue of this standard. Illustrations of examples of machines and transfer equipment to which this standard applies are shown in Annex A. Safety requirements and/or measures in this standard apply to equipment used under indoor conditions. However, additional risk assessments and safety measures need to be considered for uses in severe conditions, e.g. freezer applications, high temperatures, loads, the nature of which could lead to a dangerous situation (e.g. especially brittle loads, explosives), earthquake effects and also contact with foodstuff. Hazards during decommissioning are not covered. This European Standard also deals with the technical requirements for electromagnetic compatibility (EMC). Noise emitted by these machines is not considered as significant but as a relevant hazard. This means that the manufacturer of the machine is obliged to carry out noise reduction and indicate the noise level.

DIN EN 528:2009 Referenced Document

• EN 1037 Safety of machinery - Prevention of unexpected start-up
• EN 12385-4 Steel wire ropes - Safety - Part 4: Stranded ropes for general lifting applications
• EN 1263-1 Temporary works equipment - Safety nets - Part 1: Safety requirements@ test methods*， 2014-12-01 Update
• EN 1263-2 Temporary works equipment - Safety nets - Part 2: Safety requirements for the positioning limits*， 2014-12-01 Update
• EN 13411-3 Terminations for steel wire ropes - Safety - Part 3: Ferrules and ferrule-securing*， 2022-12-14 Update
• EN 13411-6 Terminations for steel wire ropes - Safety - Part 6: Asymmetric wedge socket
• EN 1760-1 Safety of machinery - Pressure sensitive protective devices - Part 1: General principles for the design and testing of pressure sensitive mats and pressure sensitive floors Incorporates Amendment A1: 2009
• EN 1760-2 Safety of machinery - Pressure sensitive protective devices - Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars Incorporates Amendment A1: 2009
• EN 1760-3 Safety of machinery - Pressure sensitive protective devices - Part 3: General principles for the design and testing of pressure sensitive bumpers, plates, wires and similar devices Incorporating Corrigendum January 2006; Incorporates Amendment A1: 2009
• EN 349 Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
• EN 363 Personal fall protection equipment - Personal fall protection systems
• EN 574 Safety of machinery - Two-hand control devices - Functional aspects - Principles for design
• EN 60204-32:1998 Safety of Machinery - Electrical Equipment of Machines Part 32: Requirements for Hoisting Machines
• EN 60947-5-1:2004 Low-voltage switchgear and controlgear Part 5-1: Control circuit devices and switching elements - Electromechanical control circuit devices (Incorporating Corrigendum November 2004; Incorporates Amendment A1: 2009)
• EN 61000-6-2 Electromagnetic compatibility (EMC) Part 6-2: Generic standards - Immunity for industrial environments
• EN 614-1 Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles
• EN 61496-1 Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests*， 2024-04-19 Update
• EN 795 Personal fall protection equipment - Anchor devices*， 2012-07-01 Update
• EN 81-1:1998 Safety rules for the construction and installation of lifts - Part 1: Electric lifts (Incorporates Amendment A3: 2009)
• EN 894-1 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators
• EN 894-2 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays
• EN 982 Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics Incorporates Amendment A1: 2008
• EN 999 Safety of machinery - The positioning of protective equipment in respect of approach speeds of parts of the human body Incorporates Amendment A1: 2008
• EN ISO 4871:1996 Acoustics - Declaration and Verification of Noise Emission Values of Machinery and Equipment ISO 4871: 1996

DIN EN 528:2009 history

• 2021 DIN EN 528:2021 Rail dependent storage and retrieval equipment - Safety requirements for S/R machines; German version EN 528:2021
• 1970 DIN EN 528 E:2019-09 Rail dependent storage and retrieval equipment - Safety requirements for S/R machines
• 2019 DIN EN 528 E:2019 Draft Document - Rail dependent storage and retrieval equipment - Safety requirements for S/R machines; German and English version prEN 528:2019
• 2009 DIN EN 528:2009 Rail dependent storage and retrieval equipment - Safety requirements; English version of DIN EN 528:2009-02
• 0000 DIN EN 528:2005
• 0000 DIN EN 528/A1:2003
• 0000 DIN EN 528:1996