DIN EN 792-13:2009
Hand-held non-electric power tools - Safety requirements - Part 13: Fastener driving tools; German version EN 792-13:2000+A1:2008

Standard No.

DIN EN 792-13:2009

Release Date

2009

Published By

German Institute for Standardization

Latest

DIN EN 792-13:2009

Replace

DIN EN 792-13/A1:2008 DIN EN 792-13 Berichtigung 1:2001 DIN EN 792-13:2001

Scope

This standard is applicable to fastener driving tools which are handled by one person and in which energy in a linear movement is applied to a loaded fastener for the purpose of driving this into a workpiece of a determined material. During the driving operation, the fastener leaves the tool partially or entirely, with sufficient velocity to overcome the resistance of penetration, and forms a mechanical connection or attachment of different workpieces. The energy required for driving a fastener is provided by compressed air or combustible gases. NOTE 1 Fastener driving tools are also referred to for example as Nailers, Staplers, Tackers, Pinners. NOTE 2 The workpiece material can, for example, consist of wood, wooden materials, plastic material, fibre materials - loose or condensed, cement- and lime materials, metal. This standard contains requirements for the design, marking and information for use of fastener driving tools, corresponding to the specific hazards listed in clause 4. The standard sets out the means of verification for these requirements. Where, for clarity, an example of a safety measure is given in the text, this shall not be considered as the only possible solution. Any other solution leading to the same risk reduction is permissible if an equivalent level of safety is achieved. This standard is applicable to fastener driving tools which have been produced after the date of publication of the standard. This standard is not applicable to stapling pliers and vibration hammers. NOTE 3 "Stapling pliers" are handheld power operated tools equipped with a fixed or moving anvil bar in front of the muzzle, which are used predominantly for joining paper, leather, textiles and similar materials. This standard is not applicable to fastener driving tools in which the energy for driving fasteners is drawn from cartridges or from any type of electric supply.

DIN EN 792-13:2009 Referenced Document

• EN 12096 Mechanical vibration - Declaration and verification of vibration emission values
• EN 12549:1999 Acoustics - Noise test code for fastener driving tools - Engineering method (Incorporates Amendment A1: 2008)
• EN 292-1 Safety of machinery; basic concepts, general principles for design; part 1: basic terminology, methodology
• EN 292-2 PRA1 Safety of Machinery - Basic Concepts, General Principles for Design - Part 2: Technical Principles and Specifications
• EN 349 Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
• EN 50144-1 Safety of Hand-Held Electric Motor Operated Tools - Part 1: General Requirements
• EN 563 Safety of Machinery - Temperatures of Touchable Surfaces - Ergonomics Data to Establish Temperature Limit Values for Hot Surfaces Includes Amendment A1: 1999
• EN 614-1 Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles*， 2009-02-01 Update
• EN ISO 11688-1 Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995)*， 2009-08-01 Update
• EN ISO 11690-1 Acoustics - Recommended practice for the design of low-noise workplaces containing machinery - Part 1: Noise control strategies (ISO 11690-1:2020)*， 2020-10-31 Update
• EN ISO 4871 Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)*， 2009-08-01 Update
• ISO 8662-11:1999 Hand-held portable power tools - Measurement of vibrations at the handle - Part 11: Fastener driving tools

DIN EN 792-13:2009 history

• 2009 DIN EN 792-13:2009 Hand-held non-electric power tools - Safety requirements - Part 13: Fastener driving tools; German version EN 792-13:2000+A1:2008
• 1970 DIN EN 792-13:2001 Hand-held non-electric power tools - Safety requirements - Part 13: Fastener driving tools