ASTM D2692-07
Standard Test Method for Air Wicking of Tire Fabrics, Tire Cord Fabrics, Tire Cord, and Yarns
- Standard No.
- ASTM D2692-07
- Release Date
- 2007
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D2692/D2692M-10
- Latest
- ASTM D2692/D2692M-15
- Scope
This test method is considered satisfactory for the acceptance testing of commercial shipments of tire fabrics since this test method has been used extensively in the trade for acceptance testing. This test method is also considered satisfactory for quality control.
In case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories may be compared using appropriate statistical analysis and an acceptable probability level chosen by the two parties before the testing is begun. If a bias is found, either its cause must be found and corrected or the purchaser and the supplier must agree to interpret future test results with consideration to the known bias.
This test method is applicable for testing the air permeability of any fabric that is embedded in a rubber compound, but is particularly useful when testing chafer fabrics to be used in a tubeless tire construction. In tubeless tires, chafer fabric yarns that are not wick proof represent potential channels for air to pass through, and thus, this test method provides a prediction of chafer permeability.
Evaluation of air wicking in other fabric and cord components in such products as tires, rubber brake diaphragms, and pneumatic hoses, is useful.
1.1 This test method covers the determination of longitudinal air permeability for tire fabrics, tire cord fabrics, tire cords, or yarns embedded in cured rubber compound. This test method is designed to demonstrate the effectiveness of fabric treatments intended to prevent air permeability. This test method is applicable to fabrics made from all types of fibers with all types of rubber compound.
1.2 This test method is written in SI units. The inch pound units which are provided are not necessarily exact equivalents of the SI units. Either system of units may be used in this test method.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See the Note in 11.1.
ASTM D2692-07 Referenced Document
- ASTM D123 Standard Terminology Relating to Textiles
- ASTM D3182 Standard Practice for Rubber-Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets
- ASTM D6477 Standard Terminology Relating to Tire Cord and Fabrics
ASTM D2692-07 history
- 2015 ASTM D2692/D2692M-15 Standard Test Method for Air Permeability of Tire Fabrics, Tire Cord Fabrics, Tire Cord, and Yarns
- 2010 ASTM D2692/D2692M-10(2014) Standard Test Method for Air Wicking of Tire Fabrics, Tire Cord Fabrics, Tire Cord, and Yarns
- 2010 ASTM D2692/D2692M-10 Standard Test Method for Air Wicking of Tire Fabrics, Tire Cord Fabrics, Tire Cord, and Yarns
- 2007 ASTM D2692-07 Standard Test Method for Air Wicking of Tire Fabrics, Tire Cord Fabrics, Tire Cord, and Yarns
- 2004 ASTM D2692-04 Standard Test Method for Air Wicking of Tire Fabrics, Tire Cord Fabrics, Tire Cord, and Yarns
- 1998 ASTM D2692-98 Standard Test Method for Air Wicking of Tire Fabrics, Tire Cord Fabrics, Tire Cord, and Yarns
