ASTM F1335-04
Standard Specification for Pressure-Rated Composite Pipe and Fittings for Elevated Temperature Service

Standard No.

ASTM F1335-04

Release Date

2004

Published By

American Society for Testing and Materials (ASTM)

Status

Withdraw 2011-10

Latest

ASTM F1335-04

Scope

1.1 This specification covers pressure-rated composite pipe and fittings for the transport of hot or cold liquids, beverages, or gases that are compatible with the composite pipe and fittings.

1.2 Composite pipe is produced using a butt welded aluminum pipe as a core, with an extruded inside layer of crosslinked polyethylene (PEX) or polyethylene (PE). An adhesive layer is used to bond the inside layer to the wall of the aluminum pipe. An outer layer of polyethylene (PE) and an adhesive layer are extruded to the outer wall of the aluminum pipe.

1.3 Composite pipe is produced in four configurations and referenced in Fig. 1, as Classes 1, 2, 3, and 4 composite pipe.

1.4 This specification includes compression fittings and compression joints, which are referenced in . Compression fittings as described in this specification are not compatible for gas transportation. Threaded fittings are referenced in .

1.5 The following precautionary caveat pertains only to the test method portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.6 The values stated in acceptable SI units are to be regarded as the standard. The values given in parentheses are provided for information only. The values stated in each system are not exact equivalents, therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

ASTM F1335-04 Referenced Document

• ASTM B283 Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)
• ASTM B584 Standard Specification for Copper Alloy Sand Castings for General Applications
• ASTM D1248 Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
• ASTM D1505 Standard Test Method for Density of Plastics by the Density-Gradient Technique
• ASTM D1598 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
• ASTM D1600 Standard Terminology for Abbreviated Terms Relating to Plastics
• ASTM D1898 
• ASTM D2122 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
• ASTM D2765 Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics
• ASTM D3222 Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials
• ASTM D3350 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials*， 2024-04-19 Update
• ASTM D3418 Standard Test Method for Transition Temperatures of Polymers By Differential Scanning Calorimetry
• ASTM D618 Standard Practice for Conditioning Plastics for Testing
• ASTM D638 Standard Test Method for Tensile Properties of Plastics
• ASTM F412 Standard Terminology Relating to Plastic Piping Systems
• ISO 10508 Plastics piping systems for hot and cold water installations — Guidance for classification and design AMENDMENT 1

ASTM F1335-04 history

• 2004 ASTM F1335-04 Standard Specification for Pressure-Rated Composite Pipe and Fittings for Elevated Temperature Service
• 1998 ASTM F1335-98e1 Standard Specification for Pressure-Rated Composite Pipe and Fittings for Elevated Temperature Service
• 1998 ASTM F1335-98 Standard Specification for Pressure-Rated Composite Pipe for Elevated Temperature Service