ASTM D5114-90(2004)
Standard Test Method for Laboratory Froth Flotation of Coal in a Mechanical Cell
- Standard No.
- ASTM D5114-90(2004)
- Release Date
- 1990
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D5114-90(2010)
- Latest
- ASTM D5114/D5114M-90(2018)e1
- Scope
This test method uses specific starting point conditions for the froth flotation response to accomplish the following:
4.1.1 Assess responses of one or more coals or blends of coal, and
4.1.2 Evaluate and determine froth flotation circuit performance.
1.1 This test method covers a laboratory procedure for conducting a single froth flotation test on fine coal (that is, nominal top size of 600 m (No. 30 U.S.A. Standard Sieve Series) or finer) using a defined set of starting point conditions for the operating variables.
1.2 This test method does not completely cover specific procedures for the investigation of flotation kinetics. Such a test is specialized and highly dependent upon the objective of the data.
1.3 Since optimum conditions for flotation are usually not found at the specified starting points, suggestions for development of grade/recovery curves are given in . Such a procedure is very case-specific and involves running a series of flotation tests in which some of the operating variables are changed in order to optimize conditions for either yield or grade.
1.4 Laboratory flotation results need not be representative of the flotation response of coal in full-scale situations, but a consistent baseline can be established against which full-scale performance can be compared.
1.5 The values stated in SI units are to be regarded as standard. The values in parentheses are provided for information only. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way.
This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.6 Material Safety Data Sheets (MSDS) for reagents used are to be obtained from suppliers who are to be consulted before work with any chemicals used in this test method.
ASTM D5114-90(2004) Referenced Document
- ASTM D121 Standard Terminology of Coal and Coke*， 2024-03-01 Update
- ASTM D2013 Standard Method of Preparing Coal Samples for Analysis
- ASTM D2015 Standard Test Method for Gross Caloric Value of Coal and Coke by the Adiabatic Bomb Calorimeter*， 1996-04-19 Update
- ASTM D3173 Standard Test Method for Moisture in the Analysis Sample of Coal and Coke
- ASTM D3174 Standard Test Method for Ash in the Analysis Sample of Coal and Coke from Coal*， 2018-10-15 Update
- ASTM D3177 Standard Test Methods for Total Sulfur in the Analysis Sample of Coal and Coke
- ASTM D4239 Standard Test Methods for Sulfur in the Analysis Sample of Coal and Coke Using High Temperature Tube Furnace Combustion Methods*， 1997-04-19 Update
- ASTM D4749 Standard Test Method for Performing the Sieve Analysis of Coal and Designating Coal Size
ASTM D5114-90(2004) history
- 2018 ASTM D5114/D5114M-90(2018)e1 Standard Test Method for Laboratory Froth Flotation of Coal in a Mechanical Cell
- 1990 ASTM D5114-90(2010) Standard Test Method for Laboratory Froth Flotation of Coal in a Mechanical Cell
- 1990 ASTM D5114-90(2004) Standard Test Method for Laboratory Froth Flotation of Coal in a Mechanical Cell
- 1990 ASTM D5114-90(1998) Standard Test Method for Laboratory Froth Flotation of Coal in a Mechanical Cell
- 1990 ASTM D5114-90 Standard Test Method for Laboratory Froth Flotation of Coal in a Mechanical Cell
