ASTM D7230-06
Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates
- Standard No.
- ASTM D7230-06
- Release Date
- 2006
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D7230-06(2013)
- Latest
- ASTM D7230-06(2021)
- Scope
1.1 This guide establishes procedures for evaluating lining system test specimens under simulated operating conditions.
1.2 Lining systems to be tested in accordance with this guide are intended for use in both new construction and for refurbishing existing systems or components.
1.3 The lining systems evaluated in accordance with this guide are expected to be applied to metal substrates comprising water-wetted (that is, continuous or intermittent immersion) surfaces in systems that may include:
1.3.1 Service water piping upstream of safety-related components,
1.3.2 Service water pump internals (draft tube, volutes, and diffusers),
1.3.3 Service water heat exchanger channels, pass partitions, tubesheets, end bells, and covers,
1.3.4 Service water strainers, and
1.3.5 Refueling water storage tanks and refuel cavity water storage tanks.
1.4 This guide anticipates that the lining systems to be tested include liquid-grade and paste-grade polymeric materials. Sheet type lining materials, such as rubber, are excluded from the scope of this guide.
1.5 Because of the specialized nature of these tests and the desire in many cases to simulate to some degree the expected service environment, the creation of a standard practice is not practical. This standard gives guidance in setting up tests and specifies test procedures and reporting requirements that can be followed even with differing materials, specimen preparation methods, and test facilities.
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.
ASTM D7230-06 Referenced Document
- ASTM C868 Standard Test Method for Chemical Resistance of Protective Linings
- ASTM D115 Standard Test Methods for Testing Solvent Containing Varnishes Used for Electrical Insulation
- ASTM D2240 Standard Test Method for Properties of Rubber &8212; Durometer Hardness*， 2024-04-19 Update
- ASTM D2583 Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor
- ASTM D2794 Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)
- ASTM D4060 Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
- ASTM D4082 Standard Test Method for Effects of Gamma Radiation on Coatings for Use in Light-Water Nuclear Power Plants
- ASTM D4538 Standard Terminology Relating to Protective Coating and Lining Work for Power Generation Facilities
- ASTM D4541 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
- ASTM D5139 Standard Specification for Sample Preparation for Qualification Testing of Coatings to be Used in Nuclear Power Plants
- ASTM D5144 Standard Guide for Use of Protective Coating Standards in Nuclear Power Plants*， 2024-04-19 Update
- ASTM D6677 Standard Test Method for Evaluating Adhesion by Knife
- ASTM D714 Standard Test Method for Evaluating Degree of Blistering of Paints
- ASTM D7167 Standard Guide for Establishing Procedures to Monitor the Performance of Safety-Related Coating Service Level III Lining Systems in an Operating Nuclear Power Plant
- ASTM G14 Standard Test Method for Impact Resistance of Pipeline Coatings (Falling Weight Test)
- ASTM G42 Standard Test Method for Cathodic Disbonding of Pipeline Coatings Subjected to Elevated Temperatures
ASTM D7230-06 history
- 2021 ASTM D7230-06(2021) Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates
- 2006 ASTM D7230-06(2013) Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates
- 2006 ASTM D7230-06 Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates
