ISO 15877-3:2003
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings

Standard No.

ISO 15877-3:2003

Release Date

2003

Published By

International Organization for Standardization (ISO)

Status

Withdraw

Replace By

ISO 15877-3:2009

Latest

ISO 15877-3:2009/Amd 2:2021

Scope

This Part of EN ISO 15877 specifies the characteristics of fittings made from chlorinated poly(vinyl chloride) (PVC-C) for piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) under design pressures and temperatures according to the class of application (see Table 1 of EN ISO 15877-1:2003). This standard covers a range of service conditions (application classes) and design pressure classes. For values of TD, Tmax and Tmal in excess of those in Table 1 of Part 1, this standard does not apply. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. It also specifies the parameters for the test methods referred to in this standard. In conjunction with the other Parts of EN ISO 15877:2003 (see Foreword) it is applicable to PVC-C fittings, their joints and to joints with components of PVC-C, other plastics and non-plastics materials intended to be used for hot and cold water installations. This standard is applicable to fittings of the following types: — fittings for solvent cement joints; — mechanical fittings; — fittings with incorporated inserts. NOTE 2 Fittings made from PVC-C are manufactured by injection-moulding.

ISO 15877-3:2003 Referenced Document

• EN 10088-1 Stainless steels - Part 1: List of stainless steels*， 2023-12-20 Update
• EN 12107 Plastics Piping Systems - Injection-Moulded Thermoplastics Fittings, Valves and Ancillary Equipment - Determination of the Long-Term Hydrostatic Strength of Thermoplastics Materials for Injection Moulding of Piping Components
• EN 1254-3 Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes
• EN 578 Plastics Piping Systems - Plastics Pipes and Fittings - Determination of the Opacity
• EN 681-1 Elastomeric seals Material requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber (Incorporates Amendments A1: 1998 and A2: 2002; Incorporating Corrigendum August 2002; Incorporates Amendment A3: 2005)
• EN 727 Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST)
• EN 763:1994 Plastics Piping and Ducting Systems - Injection-Moulded Thermoplastics Fittings - Test Method for Visually Assessing Effects of Heating
• EN 921:1994 Plastics Piping Systems - Thermoplastics Pipes - Determination of Resistance to Internal Pressure at Constant Temperature (Incorporating Corrigendum 1995)
• EN ISO 15877-1:2003 Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: General ISO 15877-1:2003*， 2024-04-18 Update
• EN ISO 15877-2:2003 Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Pipes ISO 15877-2:2003*， 2024-04-18 Update
• EN ISO 15877-5 Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 5: Fitness for purpose of the system - Amendment 2 (ISO 15877-5:2009/Amd 2:2020)*， 2020-11-30 Update
• EN ISO 3126 Plastics piping systems - Plastics components - Determination of dimensions ISO 3126:2005*， 2005-03-01 Update
• EN ISO 9080 Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2012)*， 2024-04-18 Update
• ISO 12092 Fittings, valves and other piping system components made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C), acrylonitrile-butadiene-styrene (ABS) and acrylonitrile-styrene-acrylester (ASA) for pipes under pressure - R
• ISO 228-1 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation

ISO 15877-3:2003 history

• 2021 ISO 15877-3:2009/Amd 2:2021 Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings; Amendment 2
• 2010 ISO 15877-3:2009/Amd 1:2010 Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings; Amendment 1
• 2009 ISO 15877-3:2009 Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings
• 2003 ISO 15877-3:2003 Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings