ASTM A1019/A1019M-01(2007)
Standard Specification for Closed Rib Steel Pipe with Diameter of 36 in. [900 mm] or Less, Polymer Precoated for Sewers and Drains

Standard No.

ASTM A1019/A1019M-01(2007)

Release Date

2001

Published By

American Society for Testing and Materials (ASTM)

Status

Withdraw 2012-05

Latest

ASTM A1019/A1019M-01(2007)

Scope

1.1 This specification covers polymer precoated, closed rib steel pipe, intended for use for storm water drainage, under-drains, the construction of culverts, and similar uses. Pipe covered by this specification is not normally used for the conveyance of sanitary or industrial wastes. The steel sheet used in fabrication of the pipe has a polymer protective coating over a metallic coating of zinc.

1.2 The polymer precoating provides extra protection of the base metal against corrosion or abrasion, or both, in addition to that provided by the metallic coating. Severe environments are likely to cause corrosion problems to accessory items such as coupling band hardware that does not have a polymer coating unless supplemental protection is provided. Additional protection for polymer precoated steel pipe is available by use of coatings applied after fabrication of the pipe as described in Specification A 849.

1.3 This specification does not include requirements for bedding, backfill, or the relationship between earth cover load and sheet thickness of the pipe. Experience with drainage products has shown that successful performance depends upon the proper selection of rib depth, sheet thickness, type of bedding and backfill, controlled manufacture in the plant, and care in installation. The installation procedure is described in Practice A 798/A 798M.

1.4 This specification is applicable to orders in either inch-pound units as A 1019, or in SI units as A 1019M. Inch-pound units and SI units are not necessarily equivalent. SI units are shown in brackets in the text for clarity, but they are the applicable values when the material is ordered to A 1019M.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM A1019/A1019M-01(2007) Referenced Document

• ASTM A307 Standard Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strangth
• ASTM A563 Standard Specification for Carbon and Alloy Steel Nuts*， 2024-04-19 Update
• ASTM A563M Standard Specification for Carbon and Alloy Steel Nuts 40;Metric41;*， 2024-04-19 Update
• ASTM A780 Standard Practice for Repair of Damaged and Uncoated Areas of Hot-Dip Galvanized Coatings
• ASTM A849 Standard Specification for Post-Applied Coatings, Pavings, and Linings for Corrugated Steel Sewer and Drainage Pipe*， 2024-04-19 Update
• ASTM A902 Standard Terminology Relating to Metallic Coated Steel Products
• ASTM B633 Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel
• ASTM B695 Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
• ASTM C443 Standard Specification for Joints for Circular Concrete Sewer and Culvert Pipe, Using Rubber Gaskets
• ASTM D1005 Standard Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers
• ASTM D1056 Standard Specification for Sponge and Expanded Cellular Rubber Products
• ASTM E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
• ASTM F568M Standard Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners

ASTM A1019/A1019M-01(2007) history

• 2001 ASTM A1019/A1019M-01(2007) Standard Specification for Closed Rib Steel Pipe with Diameter of 36 in. [900 mm] or Less, Polymer Precoated for Sewers and Drains
• 2001 ASTM A1019/A1019M-01 Standard Specification for Closed Rib Steel Pipe with Diameter of 36 in. [900 mm] or Less, Polymer Precoated for Sewers and Drains