ASTM E1461-01
Standard Test Method for Thermal Diffusivity of Solids by the Flash Method

Standard No.

ASTM E1461-01

Release Date

2001

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM E1461-07

Latest

ASTM E1461-13(2022)

Scope

Thermal diffusivity is an important property, required for such purposes as design applications under transient heat flow conditions, determination of safe operating temperature, process control, and quality assurance.

The flash method is used to measure values of thermal diffusivity, α, of a wide range of solid materials. It is particularly advantageous because of simple specimen geometry, small specimen size requirements, rapidity of measurement and ease of handling, with a single apparatus, of materials having a wide range of thermal diffusivity values over a large temperature range.

Under certain strict conditions, specific heat capacity of a homogeneous isotropic opaque solid sample can be determined when the method is used in a quantitative fashion (see Appendix X4).

Thermal diffusivity results, together with specific heat capacity (C_p) and density (ρ) values, can be used in many cases to derive thermal conductivity (λ), according to the relationship:

1.1 This test method covers the determination of the thermal diffusivity of primarily homogeneous isotropic solid materials. Thermal diffusivity values ranging from 10^-7 to 10^-3 m ²/s are readily measurable by this test method from about 75 to 2800 K.

1.2 This test method is a more detailed form of Test Method C 714, but has applicability to much wider ranges of materials, applications, and temperatures, with improved accuracy of measurements.

1.3 This test method is applicable to the measurements performed on materials opaque to the spectrum of the energy pulse, but with special precautions can be used on fully or partially transparent materials (see Appendix X1).

1.4 This test method is intended to allow a wide variety of apparatus designs. It is not practical in a test method of this type to establish details of construction and procedures to cover all contingencies that might offer difficulties to a person without pertinent technical knowledge, or to stop or restrict research and development for improvements in the basic technique.

1.5 This test method is applicable to the measurements performed on essentially fully dense materials; however, in some cases it has shown to produce acceptable results when used with porous samples. Since the magnitude of porosity, pore shapes, sizes and parameters of pore distribution influence the behavior of the thermal diffusivity, extreme caution must be exercised when analyzing data. Special caution is advised when other properties, such as thermal conductivity, are derived from thermal diffusivity obtained by this method.

1.6 This test method can be considered an absolute (or primary) method of measurement, since no reference standards are required. It is advisable to use reference materials to verify the performance of the instrument used.

1.7 This method is applicable only for homogeneous solid materials, in the strictest sense; however, in some cases it has shown to produce data which may be useful in certain applications.

1.7.1 Testing of Composite Materials--When substantial inhomogeneity and anisotropy is present in a material, the thermal diffusivity data obtained with this method may be substantially in error. Nevertheless, such data, while usually lacking absolute accuracy, may be useful in comparing materials of similar structure. Extreme caution must be exercised when related properties, such as thermal conductivity, are derived, as composites may have heat flow patterns substantially different than uniaxial.

1.7.2 Testing Liquids--This method has found an especially useful ......

ASTM E1461-01 history

• 2022 ASTM E1461-13(2022) Standard Test Method for Thermal Diffusivity by the Flash Method
• 2013 ASTM E1461-13 Standard Test Method for Thermal Diffusivity by the Flash Method
• 2011 ASTM E1461-11 Standard Test Method for Thermal Diffusivity by the Flash Method
• 2007 ASTM E1461-07 Standard Test Method for Thermal Diffusivity by the Flash Method
• 2001 ASTM E1461-01 Standard Test Method for Thermal Diffusivity of Solids by the Flash Method
• 1992 ASTM E1461-92 Standard Test Method for Thermal Diffusivity of Solids by the Flash Method