ASTM D3966-07
Standard Test Methods for Deep Foundations Under Lateral Load
- Standard No.
- ASTM D3966-07
- Release Date
- 2007
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D3966/D3966M-07(2013)e1
- Latest
- ASTM D3966/D3966M-22
- Scope
1.1 The test methods described in this standard measure the lateral deflection of a vertical or inclined deep foundation when subjected to lateral loading. These methods apply to all deep foundations, referred to herein as "pile(s)," that function in a manner similar to driven piles or cast in place piles, regardless of their method of installation, and may be used for testing single piles or pile groups. The test results may not represent the long-term performance of a deep foundation.
1.2 These test methods provide minimum requirements for testing deep foundations under lateral load. Plans, specifications, provisions, or combinations thereof prepared by a qualified engineer may provide additional requirements and procedures as needed to satisfy the objectives of a particular test program. The engineer in responsible charge of the foundation design, referred to herein as the engineer, shall approve any deviations, deletions, or additions to the requirements of these test methods.
1.3 These test methods allow the following test procedures:
1.4 Apparatus and procedures herein designated "optional" may produce different test results and may be used only when approved by the engineer. The word "shall" indicates a mandatory provision, and the word "should" indicates a recommended or advisory provision. Imperative sentences indicate mandatory provisions.
1.5 A qualified geotechnical engineer should interpret the test results obtained from the procedures of these test methods so as to predict the actual performance and adequacy of piles used in the constructed foundation. See for comments regarding some of the factors influencing the interpretation of test results.
1.6 A qualified engineer shall design and approve all loading apparatus, loaded members, support frames, and test procedures. The text of these test methods references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the test methods. These test methods also include illustrations and appendices intended only for explanatory or advisory use.
1.7 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.8 The gravitational system of inch-pound units is used when dealing with inch-pound units. In this system, the pound (lbf) represents a unit of force (weight), while the unit for mass is slugs. The rationalized slug unit is not given, unless dynamic (F=ma) calculations are involved.
1.9 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D 6026.
1.10 The method used to specify how data are collected, calculated, or recorded in these test methods is not directly related to the accuracy to which the data can be applied in design or other uses, or both. How one applies the results obtained using this standard is beyond its scope.
1.11 ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D3966-07 Referenced Document
- ASME B30.1 Stacker Cranes (Top or Under Running Bridge, Multiple Girder With Top or Under Running Trolley Hoist)
- ASME B40.100 Pressure Gauges and Gauge Attachments
- ASME B46.1 Surface Texture (Surface Roughness, Waviness, and Lay) ( - 2009)
- ASTM D1143 Standard Test Method for Piles Under Static Axial Compressive Load (Withdrawn 2006)
- ASTM D3689 Standard Test Method for Individual Piles Under Static Axial Tensile Load (Withdrawn 2005)
- ASTM D3740 Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
- ASTM D5882 Standard Test Method for Low Strain Impact Integrity Testing of Deep Foundations
- ASTM D6026 Standard Practice for Using Significant Digits in Geotechnical Data
- ASTM D653 Standard Terminology Relating to Soil, Rock, and Contained Fluids
- ASTM D6760 Standard Test Method for Integrity Testing of Concrete Deep Foundations by Ultrasonic Crosshole Testing*， 2024-04-19 Update
ASTM D3966-07 history
- 2022 ASTM D3966/D3966M-22 Standard Test Methods for Deep Foundation Elements Under Static Lateral Load
- 2007 ASTM D3966/D3966M-07(2013)e1 Standard Test Methods for Deep Foundations Under Lateral Load
- 2007 ASTM D3966-07 Standard Test Methods for Deep Foundations Under Lateral Load
- 2017 ASTM D3966-90(1995) Standard Test Method for Piles Under Lateral Loads (Withdrawn 2005)
