ASTM D7166-05
Standard Practice for Total Sulfur Analyzer Based On-line/At-line for Sulfur Content of Gaseous Fuels
- Standard No.
- ASTM D7166-05
- Release Date
- 2005
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D7166-10
- Latest
- ASTM D7166-23
- Scope
On-line, at-line, in-line and other near-real time monitoring systems that measure fuel gas characteristics such as the total sulfur content are prevalent in the natural gas and fuel gas industries. The installation and operation of particular systems vary on the specific objectives, contractual obligations, process type, regulatory requirements, and internal performance requirements needed by the user. This protocol is intended to provide guidelines for standardized start-up procedures, operating procedures, and quality assurance practices for on-line, at-line, in-line and other near-real time total sulfur monitoring systems.
1.1 This practice is for the determination of total sulfur from volatile sulfur-containing compounds in high methane or hydrogen content gaseous fuels using on-line/at-line instrumentation.
1.2 The values stated in SI units are standard. Values stated in other units are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM D7166-05 Referenced Document
- ASTM D1070 Standard Test Methods for Relative Density of Gaseous Fuels
- ASTM D1072 Standard Test Method for Total Sulfur in Fuel Gases
- ASTM D3246 Standard Test Method for Sulfur in Petroleum Gas by Oxidative Microcoulometry
- ASTM D3609 Standard Practice for Calibration Techniques Using Permeation Tubes
- ASTM D3764 Standard Practice for Validation of Process Stream Analyzer Systems
- ASTM D4298 Standard Guide for Intercomparing Permeation Tubes to Establish Traceability
- ASTM D4468 Standard Test Method for Total Sulfur in Gaseous Fuels by Hydrogenolysis and
Rateometric Colorimetry - ASTM D5287 Standard Practice for Automatic Sampling of Gaseous Fuels
- ASTM D5453 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence
- ASTM D5503 Standard Practice for Natural Gas Sample-Handling and Conditioning Systems for Pipeline Instrumentation
- ASTM D5504 Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and Chemiluminescence
- ASTM D6122 Standard Practice for Validation of Multivariate Process Infrared Spectrophotometers
- ASTM D6299 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
- ASTM D6621 Standard Practice for Performance Testing of Process Analyzers for Aromatic Hydrocarbon Materials
- ASTM D6667 Standard Test Method for Determination of Total Volatile Sulfur in Gaseous Hydrocarbons and Liquefied Petroleum Gases by Ultraviolet Fluorescence
- ASTM D6920 Standard Test Method for Total Sulfur in Naphthas, Distillates, Reformulated Gasolines, Diesels, Biodiesels, and Motor Fuels by Oxidative Combustion and Electrochemical Detection*， 2024-04-19 Update
ASTM D7166-05 history
- 2023 ASTM D7166-23 Standard Practice for Total Sulfur Analyzer Based On-line/At-line for Sulfur Content of Gaseous Fuels
- 2010 ASTM D7166-10(2015) Standard Practice for Total Sulfur Analyzer Based On-line/At-line for Sulfur Content of Gaseous Fuels
- 2010 ASTM D7166-10 Standard Practice for Total Sulfur Analyzer Based On-line/At-line for Sulfur Content of Gaseous Fuels
- 2005 ASTM D7166-05 Standard Practice for Total Sulfur Analyzer Based On-line/At-line for Sulfur Content of Gaseous Fuels
