ASTM D6776-02
Standard Test Method for Determining Anaerobic Biodegradability of Radiolabeled Plastic Materials in a Laboratory-Scale Simulated Landfill Environment

Standard No.

ASTM D6776-02

Release Date

2002

Published By

American Society for Testing and Materials (ASTM)

Status

Withdraw 2011-01

Latest

ASTM D6776-02

Scope

This method can be used to assess the anaerobic biodegradability of polymeric components of MSW such as packaging materials and to compare their biodegradability to that of materials routinely buried in landfills such as office paper and newsprint. The procedure can be completed in 6 to 9 months. This timeframe makes it possible to consider waste management during product design. The data from this method makes it possible to characterize the behavior of consumer products at the end of their useful life when they enter the solid waste management system.

Limitations8212;Because decomposition in this test is accelerated, the results reflect the ultimate biodegradability of a material in a landfill. The actual rate of degradability in a full-scale landfill will be affected by landfill environmental conditions as well as the physical characteristics of the material when actually buried.

1.1 This test method is designed to measure the anaerobic biodegradability of a material under conditions that simulate accelerated decomposition in a municipal solid waste (MSW) landfill. The test method requires the use of a ¹⁴C-labeled material so that biodegradability can be determined by monitoring for methane (¹⁴CH₄) and gaseous and aqueous carbon dioxide (¹⁴CO_2(g) and ¹⁴CO_2(aq)), which are the terminal endproducts of methanogenic decomposition. Methanogenic conditions typically control decomposition in landfills.

Note 18212;A more complete description of this decomposition is found in Reference (3).

1.2 This method could be applied to landfills that contain materials other than MSW. ¹⁴C-Radiolabeled material will be added to compost such that between 25 ci and 75 956;ci activity per 2 litres of test refuse results.

Note 28212;Adding more radiolabel is desirable because, if the material biodegrades, there will be little residual radiolabel left at the end of the decomposition experiment, which is when the refuse is removed from a reactor and analyzed for residual radiolabel to perform a mass balance. In addition, if insufficient radiolabel is added, then CH₄ and CO_2(g) production from the added refuse will dilute the ¹⁴CH₄ and ¹⁴CO_2(g) from decomposition of the test material, and the labeled gases may not be detected in the reactor offgas.

1.3 This measure of anaerobic biodegradability in the laboratory represents what will ultimately occur in a landfill over a long period. The test conditions specified here are designed to accelerate refuse decomposition such that the entire decomposition cycle can be completed in six months.

Note 38212;This cycle may require decades in a landfill depending upon the actual environmental conditions (moisture content, pH, temperature).

1.4 The measured biodegradability obtained here is compared to the biodegradability of both pure and lignified cellulose, which are chemically similar to office paper and newsprint, both of which are routinely buried in landfills.

Note 48212;The degradability of the referenced compounds is described in References (2) and (5).

At this time, there is no standard concerning the extent to which a compound must biodegrade under the test conditions described here to be considered biodegradable. Thus, this test is most appropriately used to measure biodegradability relative to pure and lignified cellulose.

1.5 The safety problems associated with refuse and radioactivity are not addressed in this standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices. It is also incumbent on the user to conform to all the regulatory requirements, specifically those that relate to the use of open radioactiv......

ASTM D6776-02 Referenced Document

• ASTM D883 Standard Terminology Relating to Plastics
• ASTM E170 Standard Terminology Relating to Radiation Measurements and Dosimetry

ASTM D6776-02 history

• 2002 ASTM D6776-02 Standard Test Method for Determining Anaerobic Biodegradability of Radiolabeled Plastic Materials in a Laboratory-Scale Simulated Landfill Environment