ASTM F1380-95a(2002)e1
Standard Specification for Metal Insert Fittings for Polybutylene (PB) Tubing

Standard No.

ASTM F1380-95a(2002)e1

Release Date

1995

Published By

American Society for Testing and Materials (ASTM)

Status

Withdraw 2008-05

Latest

ASTM F1380-95a(2002)e1

Scope

1.1 This specification covers metal insert fittings for polybutylene (PB) plastic tubing. These fittings are intended for use in 100 psi (6.9 MPa) cold- and hot-water distribution systems operating at temperatures up to and including 180176;F (82176;C). Included are the requirements for materials, workmanship, burst pressure, sustained pressure, temperature cycling tests, and markings to be used on the fittings.

1.2 The values stated in inch-pound units are to be regarded as the standard. The SI values stated in parentheses are provided for information purposes.

1.3 The following precautionary caveat pertains only to the test method portion, Section 9, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F1380-95a(2002)e1 Referenced Document

• ASTM B140/B140M Standard Specification for Copper-Zinc-Lead (Red Brass or Hardware Bronze) Rod, Bar, and Shapes*， 1997-04-19 Update
• ASTM B16 Standard Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines
• ASTM B283 Standard Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)*， 1999-04-19 Update
• ASTM B584 Standard Specification for Copper Alloy Sand Castings for General Applications*， 2022-10-01 Update
• ASTM B62 Standard Specification for Composition Bronze or Ounce Metal Castings
• ASTM B75 Standard Specification for Seamless Copper Tube*， 1999-09-10 Update
• ASTM B88 Standard Specification for Seamless Copper Water Tube*， 1999-04-19 Update
• ASTM D1598 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure*， 1997-04-19 Update
• ASTM D1599 Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings*， 1999-04-19 Update
• ASTM D1600 Standard Terminology for Abbreviated Terms Relating to Plastics*， 1999-04-19 Update
• ASTM D2122 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings*， 1998-04-19 Update
• ASTM D3309 Standard Specification for Polybutylene (PB) Plastic Hot- and Cold-Water Distribution Systems *， 1996-04-19 Update
• ASTM D618 Standard Practice for Conditioning Plastics for Testing*， 2021-07-15 Update
• ASTM D883 Standard Terminology Relating to Plastics*， 2024-02-01 Update
• ASTM F412 Standard Terminology Relating to Plastic Piping Systems*， 2023-07-20 Update

ASTM F1380-95a(2002)e1 history

• 1995 ASTM F1380-95a(2002)e1 Standard Specification for Metal Insert Fittings for Polybutylene (PB) Tubing
• 1995 ASTM F1380-95a(2002) Standard Specification for Metal Insert Fittings for Polybutylene (PB) Tubing
• 1995 ASTM F1380-95a Standard Specification for Metal Insert Fittings for Polybutylene (PB) Tubing