ISO 13631:2002
Petroleum and natural gas industries - Packaged reciprocating gas compressors

Standard No.

ISO 13631:2002

Release Date

2002

Published By

International Organization for Standardization (ISO)

Latest

ISO 13631:2002

Scope

This International Standard gives requirements and recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of packaged skid-mounted, reciprocating, separable or integral compressors with lubricated cylinders and their prime movers, for use in the petroleum and natural gas industries for the compression of hydrocarbon gas. It is also applicable to all necessary auxiliary equipment, such as water and gas coolers, silencers, emission control equipment, filters, separators, control panel, piping, etc., required to install an operable unit in compliance with the purchase specifications and with the intent of minimizing field construction and field-purchased equipment. This International Standard is not applicable to the following: — reciprocating compressors for petroleum and natural gas industries covered by ISO 13707; — column-mounted compressors; — non-lubricated compressors; — compressors having trunk-type (automotive-type) pistons that also serve as crossheads; — utility or instrument air compressors with a discharge gauge pressure of 0,9 MPa (9 bar) or less; — compressors driven by diesel engine, gas turbine and steam turbine prime movers.

ISO 13631:2002 Referenced Document

• ASME VIII RULES FOR CONSTRUCTION OF PRESSURE VESSELS
• EN 10213-1:1995 Technical Delivery Conditions for Steel Castings for Pressure Purposes - Part 1: General
• EN 10213-2:1995 Technical Delivery Conditions for Steel Castings for Pressure Purposes - Part 2: Steel Grades for Use at Room Temperature and Elevated Temperatures
• EN 10213-3:1995 Technical Delivery Conditions for Steel Castings for Pressure Purposes - Part 3: Steel Grades for Use at Low Temperatures [Superseded By: CEN EN 10213, CEN EN 10213]
• EN 10213-4:1995 Technical Delivery Conditions for Steel Castings for Pressure Purposes - Part 4: Austenitic and Austenitic-Ferritic Steel Grades
• EN 10269 Steels and nickel alloys for fasteners with specified elevated and/or low temperature properties*， 2024-04-17 Update
• IEC 60034 Rotating electrical machines - ALL PARTS*， 2018-01-08 Update
• IEC 60079 Explosive atmospheres - ALL PARTS*， 2018-01-08 Update
• IEC 60364-5 Low-voltage electrical installations - Part 5-57: Selection and erection of electrical equipment - Erection of stationary secondary batteries*， 2022-10-20 Update
• IEC 60529 Degrees of Protection Provided by Enclosures (IP Code) (Edition 2.1 ***Applies to French text only***)*， 2024-04-17 Update
• IEC 60848 GRAFCET specification language for sequential function charts*， 2013-02-01 Update
• ISO 10441 Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - Special-purpose applications*， 2007-03-01 Update
• ISO 13707 Petroleum and natural gas industries - Reciprocating compressors
• ISO 14691 Petroleum, petrochemical and natural gas industries - Flexible couplings for mechanical power transmission - General-purpose applications*， 2008-12-01 Update
• ISO 15649 Petroleum and natural gas industries - Piping
• ISO 1813 Belt drives - V-ribbed belts, joined V-belts and V-belts including wide section belts and hexagonal belts - Electrical conductivity of antistatic belts: Characteristics and methods of test*， 2014-02-01 Update
• ISO 185 Grey cast irons — Classification*， 2020-05-29 Update
• ISO 261 ISO general purpose metric screw threads - General plan
• ISO 262 ISO general purpose metric screw threads — Selected sizes for bolts, screws, studs and nuts*， 2023-04-01 Update
• ISO 263:1973 ISO inch screw threads; General plan and selection for screws, bolts and nuts; Diameter range 0,06 to 6 in
• ISO 281 Rolling bearings - Dynamic load ratings and rating life*， 2007-02-01 Update
• ISO 4126-1:1991 Safety valves; part 1: general requirements
• ISO 4986:1992 Steel castings; magnetic particle inspection
• ISO 5864:1993 ISO inch screw threads; allowances and tolerances
• ISO 68-2:1998 ISO general purpose screw threads - Basic profile - Part 2: Inch screw threads
• ISO 7-1 Pipe threads where pressure-tight joints are made on the threads — Part 1: Dimensions, tolerances and designation TECHNICAL CORRIGENDUM 1
• ISO 7005-1 Pipe flanges - Part 1: Steel flanges for industrial and general service piping systems*， 2011-07-01 Update
• ISO 7005-2 Metallic flanges; part 2: cast iron flanges
• ISO 8504-2 Preparation of steel substrates before application of paints and related products — Surface preparation methods — Part 2: Abrasive blast-cleaning*， 2019-10-31 Update
• ISO 9934-2 Non-destructive testing - Magnetic particle testing - Part 2: Detection media*， 2015-09-01 Update

ISO 13631:2002 history

• 2002 ISO 13631:2002 Petroleum and natural gas industries - Packaged reciprocating gas compressors