DIN EN 13476-1:2007
Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: General requirements and performance characterist

Standard No.

DIN EN 13476-1:2007

Release Date

2007

Published By

German Institute for Standardization

Status

Be replaced 2018-10

Replace By

DIN EN 13476-1:2018

DIN EN 13476-1 E:2015-11

Latest

DIN EN 13476-1:2024-03

Replace

DIN EN 13476-1:2006

Scope

This European Standard, together with EN 13476-2 and EN 13476-3, specifies the definitions and general requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene(PP) and polyethylene(PE) structured-wall piping system that are to be used for non-pressure underground drainage and sewerage systems. This standard is applicable to: a) strutured-wall pipes and fittings, which are to be used buried in the ground outside a building structure only; reflected by the marking of products by"U"; b) structured-wall pipes and fittings, which are to be used buried in the ground both outside(application area code"U") and within a building structure(application area code"D"); reflected in the marking of products by"UD". In cojunction with EN 13476-2 and EN 13476-3 it is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints, as well as welded and fused joints. This part specifies general aspects and gives guidance concerning a national selection of requirement levels and classes where part 2 and part 3 of this standard provide options. EN 13476-2 and 13476-3 specify material characteristics, dimensions and tolerances, test methods, test parameters and requirements for pipes with smooth internal and external surfaces, Type A, and pipes with smooth internal and profiled external surfaces, Type B. This standard, together with EN 13476-2 and EN 13476-3, covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes and tolerance classes and offers recommendation concerning colours. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. NOTE 2 Pipes,n fittings and other components conforming to any plastic product standards referred to in clause 2 can be used with pipes and fittings conforming to this standard, when they conform to the requirements for joint dimensions given in part 2 and part 3 of this standard and to the performance requirements given in Clause 9. NOTE 3 For dimension larger than DN 1200 OD/ID this document may serve as general guideline regarding appearance, colour, physical and mechanical characteristics as well as performance requirements.

DIN EN 13476-1:2007 Referenced Document

• EN 13476-2:2007 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and fittings with smooth
• EN 13476-3:2007 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 3: Specifications for pipes and fittings with smooth
• EN 681-1 Elastomeric seals Material requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber (Incorporates Amendments A1: 1998 and A2: 2002; Incorporating Corrigendum August 2002; Incorporates Amendment A3: 2005)
• EN 681-2 Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers
• EN 681-4 Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 4: Cast polyurethane sealing elements
• EN ISO 1043-1:2001 Plastics - Symbols and Abbreviated Terms - Part 1: Basic Polymers and Their Special Characteristics
• EN ISO 472:2001 Plastics - Vocabulary
• EN ISO 9969 Thermoplastics pipes - Determination of ring stiffness*， 2016-01-01 Update
• ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids - Dimensions and tolerances - Part 1: Metric series
• ISO 13967 Thermoplastics fittings - Determination of ring stiffness*， 2009-12-01 Update

DIN EN 13476-1:2007 history

• 2024 DIN EN 13476-1:2024-03 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: General requirements and performance character...
• 2018 DIN EN 13476-1:2018-10 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: General requirements and performance character...
• 2018 DIN EN 13476-1:2018 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: General requirements and performance characterist
• 2007 DIN EN 13476-1:2007 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: General requirements and performance characterist
• 0000 DIN EN 13476-1:2006