DIN EN 13476-2:2007
Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and fittings with smooth

Standard No.

DIN EN 13476-2:2007

Release Date

2007

Published By

German Institute for Standardization

Status

Be replaced

Replace By

DIN EN 13476-2:2018

DIN EN 13476-2 E:2015-11

Latest

DIN EN 13476-2 A1 E:2019-05

DIN EN 13476-2:2018

DIN EN 13476-2:2020-12

DIN EN 13476-2 E:2015-11

Replace

DIN EN 13476-2:2006

Scope

This part of EN 13476, together with EN 13476-1, specifies the definitions and requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene(PP) and polyethylene(PE) structured-wall piping system that are intended to be used for non-pressure underground drainage and sewerage systems. This part is applicable to pipes and fittings with smooth internal and external surfaces, designated as Type A. It specifies test methods and test parameters as well as requirements. This part is applicalbe to: a) strutured-wall pipes and fittings, which are intended to be used buried underground outside the building structure;reflected in the marking of products by"U"; b) structured-wall pipes and fittings, which are intended to be used buried underground both outside(application area code"U") and within a building structure(application area code"D"); reflected in the marking of products by"UD". This part is applicable to structured-wall pipes and fittings with or without an integral socket with elastomeric ring seal joints as well as welded and fused joints. This part covers a range of pipe and fitting sizes, materials, pipe constructions, stiffness classes, application classes, and tolerance classes and gives recommendations concerning colours. NOTE 1 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. NOTE 2 For dimension larger than DN 1200 OD/ID this document may be applied regarding appearance, colour, physical and mechanical characteristics as well as performance requirements.

DIN EN 13476-2:2007 Referenced Document

• EN 1053 Plastics piping systems - Thermoplastics piping systems for non-pressure applications - Test method for watertightness
• EN 1055:1996 Plastics piping systems - Thermoplastics piping systems for soil and waste discharge inside buildings - Test method for resistance to elevated temperature cycling
• EN 12061 Plastics piping systems - Thermoplastics fittings - Test method for impact resistance
• EN 12256 Plastics piping systems - Thermoplastics fittings - Test method for mechanical strength or flexibility of fabricated fittings
• EN 12666-1 Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system*， 2011-08-01 Update
• EN 1277 Plastics piping systems - Thermoplastics piping systems for buried non-pressure applications - Test methods for leaktightness of elastomeric sealing ring type joints*， 2024-04-18 Update
• EN 13476-1:2007 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 1: General requirements and performance characterist
• EN 13476-3 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U)@ polypropylene (PP) and polyethylene (PE) - Part 3: Specifications for pipes and fittings with smooth*， 2019-04-01 Update
• EN 1401-1 Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system*， 2009-03-01 Update
• EN 1411 Plastics piping and ducting systems - Thermoplastics pipes - Determination of resistance to external blows by the staircase method
• EN 1437 Plastics piping systems - Piping systems for underground drainage and sewerage - Test method for resistance to combined temperature cycling and external loading
• EN 1446 Plastics Piping and Ducting Systems - Thermoplastics Pipes - Determination of Ring Flexibility
• EN 14741 Thermoplastics piping and ducting systems - Joints for buried non-pressure applications - Test method for the long-term sealing performance of joints with elastomeric seals by estimating the sealing pressure
• EN 14758-1 Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system*， 2012-03-01 Update
• EN 1852-1 Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Part 1: Specifications for pipes@ fittings and the system*， 2018-01-01 Update
• EN 1905 Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material - Method for assessment of the PVC content based on total chlorine content
• EN 1979 Plastics Piping and Ducting Systems - Thermoplastics Spirally - Formed Structured-Wall Pipes - Determination of the Tensile Strength of a Seam
• EN 476 General requirements for components used in drains and sewers*， 2011-01-01 Update
• EN 580 Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes - Test method for the resistance to dichloromethane at a specified temperature (DCMT)
• EN 681-1 Elastomeric seals Material requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber (Incorporates Amendments A1: 1998 and A2: 2002; Incorporating Corrigendum August 2002; Incorporates Amendment A3: 2005)
• EN 681-2 Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers
• EN 681-4 Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 4: Cast polyurethane sealing elements
• EN 727 Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST)
• EN 728 Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time
• EN 744 Plastics piping and ducting systems - Thermoplastics pipes - Test method for resistance to external blows by the round-the-clock method
• EN 922 Plastics Piping and Ducting Systems - Pipes and Fittings of Unplasticized Poly(Vinyl Chloride) (PVC-U) - Specimen Preparation for Determination of the Viscosity Number and Calculation of the K-Value

DIN EN 13476-2:2007 history

• 2020 DIN EN 13476-2:2020 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and fittings with smooth
• 1970 DIN EN 13476-2 A1 E:2019-05
• 0000 DIN EN 13476-2/A1:2019
• 2018 DIN EN 13476-2:2018 Plastics piping systems for non-pressure underground drainage and sewerage – Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) – Part 2: Specifications for pipes and fittings with smooth
• 2007 DIN EN 13476-2:2007 Plastics piping systems for non-pressure underground drainage and sewerage - Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) - Part 2: Specifications for pipes and fittings with smooth
• 0000 DIN EN 13476-2:2006