DIN EN 1993-1-5:2007 PDF

Standard No.: DIN EN 1993-1-5:2007
Release Date: 2007
Published By: German Institute for Standardization
Status: Withdraw
Replace By: DIN EN 1993-1-5:2010; DIN EN 1993-1-5 NA E:2009-05
Latest: DIN EN 1993-1-5:2022-03

Scope: (1) EN 1993-1-5 gives design requirements of stiffened and unstiffened paltes which are subject to in-plane forces. (2) Effects due to shear lag, in-plane load introduction and plate bucking for I-section girders and box girders are covered. Also covered are plated structural components subject to in-plane loads as in tanks and silos. The effects of out-of-plane loading are outside the scope of this document. NOTE 1: The rules in this part complement the rules for class 1, 2, 3 and 4 section, see EN 1993-1-1. NOTE 2: For the design of slender plates which are subject to repeated direct stress and/or shear and also fatigue due to out-of-plane bending of plate elements (breathing) see EN 1993-2 and EN 1993-6. NOTE 3: For the effects of out-of-plane loading and for the combination of in-plane effects and out-of-plane loading effects see EN 1993-2 and EN 1993-1-7. NOTE 4: Single plate elements may be considered as flat where the curvature radius r satisfies: r ≥ a/t (1.1) where a is the panel width t is the plate thickness

DIN EN 1993-1-5:2007 history

2022 DIN EN 1993-1-5:2022-03 Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements; German and English version prEN 1993-1-5:2022 / Note: Date of issue 2022-02-11*Intended as replacement for DIN EN 1993-1-5 (2019-10), DIN EN 1993-1-5 Berichtigung 1 (2020-07).
2022 DIN EN 1993-1-5:2022 Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements; German and English version prEN 1993-1-5:2022
2020 DIN EN 1993-1-5 Berichtigung 1:2020-07 Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements; German version EN 1993-1-5:2006 + AC:2009 + A1:2017 + A2:2019; Corrigendum 1 / Note: To be replaced by DIN EN 1993-1-5 (2022-03).
2019 DIN EN 1993-1-5:2019-10 Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements; German version EN 1993-1-5:2006 + AC:2009 + A1:2017 + A2:2019 / Note: To be replaced by DIN EN 1993-1-5 (2022-03).
1970 DIN EN 1993-1-5 A2 E:2019-03
2019 DIN EN 1993-1-5:2019 Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements
2018 DIN EN 1993-1-5/NA:2018-11 National Annex - Nationally determined parameters - Eurocode 3: Design of steel structures - Part 1-5: Plated structural elements / Note: Applies in conjunction with DIN EN 1993-1-5 (2017-07).
1970 DIN EN 1993-1-5 NA A1 E:2018-06
2018 DIN EN 1993-1-5/NA:2018 National Annex - Nationally determined parameters - Eurocode 3: Design of steel structures - Part 1-5: Plated structural elements
2017 DIN EN 1993-1-5:2017 Eurocode 3 - Design of steel structures - Part 1-5: Plated structural elements; German version EN 1993-1-5:2006 + AC:2009 + A1:2017
2010 DIN EN 1993-1-5:2010 Eurocode 3: Design of steel structures - Part 1-5: Plated structural elements; German version EN 1993-1-5:2006 + AC:2009
2007 DIN EN 1993-1-5:2007 Eurocode 3: Design of steel structures - Part 1-5: Plated structural elements; German version EN 1993-1-5:2006

Eurocode 3: Design of steel structures - Part 1-5: Plated structural elements; German version EN 1993-1-5:2006

DIN EN 1993-1-5:2007Eurocode 3: Design of steel structures - Part 1-5: Plated structural elements; German version EN 1993-1-5:2006

DIN EN 1993-1-5:2007 history

DIN EN 1993-1-5:2007
Eurocode 3: Design of steel structures - Part 1-5: Plated structural elements; German version EN 1993-1-5:2006