DIN EN 1993-1-3:2007
Eurocode 3: Design of steel structures - Part 1-3: General rules - Supplementary rules for cold-formed members and sheeting; German version EN 1993-1-3:2006

Standard No.

DIN EN 1993-1-3:2007

Release Date

2007

Published By

German Institute for Standardization

Status

Withdraw

Replace By

DIN EN 1993-1-3:2010

DIN EN 1993-1-3 NA:2008

Latest

DIN EN 1993-1-3:2022-03

Scope

(1) EN 1993-1-3 gives design requirements for cold-formed thin gauge members and sheeting. It applies to cold-formed steel products made from coated or uncoated thin gauge hot or cold rolled sheet or strip, that have been cold-formed by such processes as cold-rolled forming or press-braking. It may also be used for the design of profiled steel sheeting for composite steel and concrete slabs at the construction stage, see EN 1994. The execution of steel structures made of cold-formed thin gauge members and sheeting is covered in EN 1090. NOTE: The rules in this part complement the rules in other parts of EN 1993-1. (2) Methods are also given for stressed-skin design using steel sheeting as a structural diaphragm. (3) This part does not apply to cold-formed circular and rectangular structural hollow sections supplied to EN 10219, for which reference should be made to EN 1993-1-1 and EN 1993-1-8. (4) EN 1993-1-3 gives methods for design by caculation and for design assisted by testing. The methods for design by calucation apply only within stated ranges of material properties and geometrical proportions for which sufficient experience and test evidence is available. These limitation do not apply to design assisted by testing. (5) EN 1993-1-3 does not cover load arrangement for testing for loads during execution and maintenance. (6) The calculation rules given in this standard are only valid if the tolerances of the cold formed members comply with EN 1090-2

DIN EN 1993-1-3:2007 history

• 2022 DIN EN 1993-1-3:2022-03 Eurocode 3 - Design of steel structures - Part 1-3: General rules - Supplementary rules for cold-formed members and sheeting; German and English version prEN 1993-1-3:2022 / Note: Date of issue 2022-02-11*Intended as replacement for DIN EN 1993-1-3 (20...
• 2022 DIN EN 1993-1-3:2022 Eurocode 3 - Design of steel structures - Part 1-3: General rules - Supplementary rules for cold-formed members and sheeting; German and English version prEN 1993-1-3:2022
• 2017 DIN EN 1993-1-3/NA:2017-05 National Annex - Nationally determined parameters - Eurocode 3: Design of steel structures - Part 1-3: General rules - Supplementary rules for cold-formed members and sheeting / Note: Applies in conjunction with DIN EN 1993-1-3 (2010-12).
• 2017 DIN EN 1993-1-3/NA:2017 National Annex - Nationally determined parameters - Eurocode 3: Design of steel structures - Part 1-3: General rules - Supplementary rules for cold-formed members and sheeting
• 1970 DIN EN 1993-1-3 NA A1 E:2016-08
• 2010 DIN EN 1993-1-3:2010-12 Eurocode 3: Design of steel structures - Part 1-3: General rules - Supplementary rules for cold-formed members and sheeting; German version EN 1993-1-3:2006 + AC:2009 / Note: To be replaced by DIN EN 1993-1-3 (2022-03).
• 2010 DIN EN 1993-1-3:2010 Eurocode 3: Design of steel structures - Part 1-3: General rules - Supplementary rules for cold-formed members and sheeting; German version EN 1993-1-3:2006 + AC:2009
• 2007 DIN EN 1993-1-3:2007 Eurocode 3: Design of steel structures - Part 1-3: General rules - Supplementary rules for cold-formed members and sheeting; German version EN 1993-1-3:2006