ASTM E2749-15a(2019)
Standard Practice for Measuring the Uniformity of Furnace Exposure on Test Specimens
- Standard No.
- ASTM E2749-15a(2019)
- Release Date
- 2019
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM E2749-23
- Latest
- ASTM E2749-23a
- Scope
- 1.1 This standard provides general principles for measuring the uniformity of the furnace exposure on specimens tested in accordance with Test Methods E119, E814, E1529, E1725, E1966 and E2336. 1.2 This practice specifies the materials and the construction requirements for a standardized test specimen used to provide a mounting surface for the instrumentation that measures furnace exposure. 1.3 The instrumentation records temperatures, pressure differentials, and oxygen content near the surface of the test specimen. 1.4 The values stated in SI units are to be regarded as the standard. The units given in parentheses are for information only. 1.5 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.6 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM E2749-15a(2019) Referenced Document
- ASTM C1396/C1396M Standard Specification for Gypsum Board*， 2024-04-22 Update
- ASTM E119 Standard Test Methods for Fire Tests of Building Construction and Materials
- ASTM E1529 Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies*， 2022-04-01 Update
- ASTM E1725 Standard Test Methods for Fire Tests of Fire-Resistive Barrier Systems for Electrical System Components
- ASTM E176 Standard Terminology of Fire Standards
- ASTM E1966 Standard Test Method for Fire-Resistive Joint Systems
- ASTM E2336 Standard Test Methods for Fire Resistive Grease Duct Enclosure Systems*， 2020-04-01 Update
- ASTM E814 Standard Test Method for Fire Tests of Penetration Firestop Systems*， 2023-07-01 Update
- ISO/TR 834-2 Fire-resistance tests - Elements of building construction - Part 2: Guidance on measuring uniformity of furnace exposure on test samples
ASTM E2749-15a(2019) history
- 2023 ASTM E2749-23a Standard Practice for Measuring the Uniformity of Furnace Exposure on Test Specimens
- 2023 ASTM E2749-23 Standard Practice for Measuring the Uniformity of Furnace Exposure on Test Specimens
- 2019 ASTM E2749-15a(2019) Standard Practice for Measuring the Uniformity of Furnace Exposure on Test Specimens
- 2015 ASTM E2749-15a Standard Practice for Measuring the Uniformity of Furnace Exposure on Test Specimens
- 2015 ASTM E2749-15 Standard Practice for Measuring the Uniformity of Furnace Exposure on Test Specimens
- 2010 ASTM E2749-10(2014) Standard Practice for Measuring the Uniformity of Furnace Exposure on Test Specimens
- 2010 ASTM E2749-10 Standard Practice for Measuring the Uniformity of Furnace Exposure on Test Specimens
