ASTM C387/C387M-17
Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar
- Standard No.
- ASTM C387/C387M-17
- Release Date
- 2017
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM C387/C387M-23
- Latest
- ASTM C387/C387M-23
- Scope
-
1.1 This specification covers the production, properties, packaging, and testing of packaged, dry, combined materials for concrete and high strength mortar. The classifications of concrete and mortar covered are defined in Section 3.
Note 1: The scope of this standard does not cover mortars for unit masonry. Dry preblended mortars for unit masonry are covered by Specification C1714/C1714M.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Some values have only SI units because the inch-pound equivalents are not used in practice.
1.3 The following safety hazards caveat pertains only to the test method portion of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM C387/C387M-17 Referenced Document
- ASTM C109/C109M Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)
- ASTM C1116 Standard Specification for Fiber-Reinforced Concrete and Shotcrete*， 2024-04-22 Update
- ASTM C1157 Standard Performance Specification for Hydraulic Cement*， 2024-04-22 Update
- ASTM C1240 Standard Specification for Silica Fume Used in Cementitious Mixtures*， 2020-01-15 Update
- ASTM C125 Standard Terminology Relating to Concrete and Concrete Aggregates*， 2021-10-01 Update
- ASTM C1329 Standard Specification for Mortar Cement*， 2024-04-22 Update
- ASTM C138/C138M Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete*， 2023-08-01 Update
- ASTM C143/C143M Standard Test Method for Slump of Hydraulic-Cement Concrete*， 2020-06-01 Update
- ASTM C1437 Standard Test Method for Flow of Hydraulic Cement Mortar
- ASTM C1438 Standard Specification for Latex and Powder Polymer Modifiers for Hydraulic Cement Concrete and Mortar
- ASTM C144 Standard Specification for Aggregate for Masonry Mortar
- ASTM C150 Standard Specification for Portland Cement
- ASTM C1600/C1600M Standard Specification for Rapid Hardening Hydraulic Cement*， 2023-06-15 Update
- ASTM C1714/C1714M Standard Specification for Preblended Dry Mortar Mix for Unit Masonry*， 2023-08-15 Update
- ASTM C173/C173M Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method*， 2024-01-01 Update
- ASTM C185 Standard Test Method for Air Content of Hydraulic Cement Mortar
- ASTM C192/C192M Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory*， 2019-12-01 Update
- ASTM C207 Standard Specification for Hydrated Lime for Masonry Purposes
- ASTM C231 Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method
- ASTM C260 Standard Specification for Air-Entraining Admixtures for Concrete
- ASTM C270 Standard Specification for Mortar For Unit Masonry
- ASTM C305 Standard Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency
- ASTM C33 Standard Specification for Concrete Aggregates
- ASTM C330 Standard Specification for Lightweight Aggregates For Structural Concrete
- ASTM C39/C39M Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens
- ASTM C494/C494M Standard Specification for Chemical Admixtures for Concrete
- ASTM C566 Standard Test Method for Total Evaporable Moisture Content of Aggregate by Drying
- ASTM C595 Standard Specification for Blended Hydraulic Cements
- ASTM C618 Standard Specification for Fly Ash And Raw Or Calcined Natural Pozzolan For Use As A Mineral Admixture In Portland Cement Concrete
- ASTM C702 Standard Practice for Reducing Samples of Aggregate to Testing Size
- ASTM C91 Standard Specification for Masonry Cement
- ASTM C989 Standard Specification for Ground Granulated Blast-Furnace Slag for Use in Concrete and Mortars
ASTM C387/C387M-17 history
- 2023 ASTM C387/C387M-23 Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar
- 2017 ASTM C387/C387M-17 Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar
- 2015 ASTM C387/C387M-15 Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar
- 2011 ASTM C387/C387M-11b Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar
- 2011 ASTM C387/C387M-11a Standard Specification for Packaged, Dry, Combined Materials for Mortar and Concrete
- 2011 ASTM C387/C387M-11 Standard Specification for Packaged, Dry, Combined Materials for Mortar and Concrete
- 2010 ASTM C387/C387M-10 Standard Specification for Packaged, Dry, Combined Materials for Mortar and Concrete
- 2009 ASTM C387/C387M-09 Standard Specification for Packaged, Dry, Combined Materials for Mortar and Concrete
- 2008 ASTM C387/C387M-08 Standard Specification for Packaged, Dry, Combined Materials for Mortar and Concrete
- 2006 ASTM C387/C387M-06a Standard Specification for Packaged, Dry, Combined Materials for Mortar and Concrete
- 2006 ASTM C387-06 Standard Specification for Packaged, Dry, Combined Materials for Mortar and Concrete
- 2004 ASTM C387-04 Standard Specification for Packaged, Dry, Combined Materials for Mortar and Concrete
- 2000 ASTM C387-00e1 Standard Specification for Packaged, Dry, Combined Materials for Mortar and Concrete
- 2000 ASTM C387-00 Standard Specification for Packaged, Dry, Combined Materials for Mortar and Concrete
